Refer to the exhibit. MPLS has been enabled on router PE11. Which of these statements is correct regarding the output display shown in the exhibit? （）
A. CEF switching is not needed for MPLS operation.
B. CEF switching is only needed to forward labeled packets.
C. CEF switching is needed on both ingress and egress interfaces on which MPLS is enabled.
D. Interface-level CEF switching is needed only on egress interfaces that are sending IP packets on which the egress LSR performs the label imposition process.
E. Interface-level CEF switching is needed only on ingress interfaces that are receiving IP packets on which the ingress LSR performs the label imposition process.
您可能感興趣的試卷
你可能感興趣的試題
A. If using IS-IS as the PE-CE routing protocol, no redistribution is required.
B. If using static routes between the CE and PE routers, no redistribution of other VPN routes is required.
C. If the PE-CE protocol is not BGP, redistribution of other VPN routes from MP-BGP is required.
D. If RIP is the routing protocol that is used between the PE-CE routers, no redistribution is required, but any other protocol will require redistribution.
E. If using OSPF or EIGRP as the PE-CE routing protocol, redistribution is not required, but any other protocol or static route will require redistribution.
A. NetFlow can report on the number of traffic matches for each class map in a configured QoS policy configuration.
B. NetFlow records can be used to understand traffic profiles per class of service for data, voice, and video traffic.
C. NetFlow can discover the protocols in use and automatically adjust QoS traffic classes to meet policy-map requirements.
D. NetFlow can be configured to identify voice and video traffic flows and place them into a low-latency queue for expedited processing.
A. Layer 2 TTL
B. Layer 3 TTL
C. Layer 3 source address
D. Layer 3 transport protocol
E. Layer 3 destination address
A.interfacevlan100ipaccess-grouptest
B.interfacevlan100ipaccess-grouptestin
C.interfacevlan100ipaccess-grouptestout
D.vlanfiltertestvlan-list100
E.vlanaccess-maptest100
A. by snooping the CoS marking on the incoming frames
B. by using RTP hello messages between the switch port and the Cisco IP Phone
C. by using CDP
D. by using DHCP snooping
E. by snooping the incoming 802.1Q VLAN tag
最新試題
Which keyword is used with the show ip bgp neighbors [keyword] command to display all routes that are received and accepted from a neighbor?（）
What is the most likely reason that an IBGP route that has been selected as a best route is not entered into the IP routing table?（）
As an experienced network engineer, you are asked to troubleshoot a CIS network outage. During the troubleshooting process, you notice that one of your colleagues connects additional devices to the network with the use of his own switch. With the purpose of improving speed, the switch is attached to both network ports in an office, which leads to bridge loop.Enabling which of the following feature will be able to prevent this problem from happening again?（）
Which of the following allows network administrators to easily apply common services and employ features across Cisco switches, routers, and access points with an intuitive GUI?（）
What is the function of the no switchport catalyst switch interface configuration command?（）
Referring to the partial Cisco Catalyst switch configuration shown, which two of these statements are correct? （）(Choose two.)
In a high-availability network, which command, when placed on ports that have connected end stations, will allow you to prevent delays in service for end stations by placing a port in blocking mode?（）
When a Cisco router is configured for SSH, it acts as an （）?
Refer to the exhibit. You have a non-Cisco switch that is not communicating properly while connected to the distribution-layer Cisco switching fabric.Which two best-practice actions can you take to overcome this problem? （）(Choose two.)
Refer to the exhibit. Which two of these events will be the result of issuing the above command? （）(Choose two.)