A. If using IS-IS as the PE-CE routing protocol, no redistribution is required.
B. If using static routes between the CE and PE routers, no redistribution of other VPN routes is required.
C. If the PE-CE protocol is not BGP, redistribution of other VPN routes from MP-BGP is required.
D. If RIP is the routing protocol that is used between the PE-CE routers, no redistribution is required, but any other protocol will require redistribution.
E. If using OSPF or EIGRP as the PE-CE routing protocol, redistribution is not required, but any other protocol or static route will require redistribution.
您可能感興趣的試卷
你可能感興趣的試題
A. NetFlow can report on the number of traffic matches for each class map in a configured QoS policy configuration.
B. NetFlow records can be used to understand traffic profiles per class of service for data, voice, and video traffic.
C. NetFlow can discover the protocols in use and automatically adjust QoS traffic classes to meet policy-map requirements.
D. NetFlow can be configured to identify voice and video traffic flows and place them into a low-latency queue for expedited processing.
A. Layer 2 TTL
B. Layer 3 TTL
C. Layer 3 source address
D. Layer 3 transport protocol
E. Layer 3 destination address
A.interfacevlan100ipaccess-grouptest
B.interfacevlan100ipaccess-grouptestin
C.interfacevlan100ipaccess-grouptestout
D.vlanfiltertestvlan-list100
E.vlanaccess-maptest100
A. by snooping the CoS marking on the incoming frames
B. by using RTP hello messages between the switch port and the Cisco IP Phone
C. by using CDP
D. by using DHCP snooping
E. by snooping the incoming 802.1Q VLAN tag
Refer to the exhibit. Users complain that they intermittently lose data and connections to important servers. After investigation, you discover that the 802.1Q trunk between DSW111 and ASW1 is down.
Even though the HSRP group 11 is being serviced by DSW112, you discover that the SVI for VLAN 11 is in the up state on DSW111.
Which three Cisco Catalyst IOS commands should you use on DSW111 to find the source of this problem? （）(Choose three.)
A. show vtp status
B. show interfaces vlan 11
C. show standby vlan 11 brief
D. show spanning-tree vlan 11
E. show interfaces
最新試題
When a Cisco router is configured for SSH, it acts as an （）?
What is the purpose of using VPN hardware acceleration equipment?（）
Which keyword is used with the debug ipv6 [keyword] command to troubleshoot neighbor discovery problems?（）
On the Catalyst 6500 Series switch, which command is used to establish a console connection to the Firewall Services Module?（）
You are an experienced network administrator in an international corporation. One of your clients asks you to configure a network for a financial trading center which requires multiple high-value transactions.And the transactions are very important to the client. In such a situation, which two of the following are basic and most important requirements concerning the configuration? （）(Choose two.)
Refer to the exhibit. You have a non-Cisco switch that is not communicating properly while connected to the distribution-layer Cisco switching fabric.Which two best-practice actions can you take to overcome this problem? （）(Choose two.)
Refer to the exhibit. You want to minimize the downtime that results from supervisor engine switchovers on Cisco 6500 Series Switches and Cisco 7600 Series Routers. To achieve this, you are considering deploying a Cisco Nonstop Forwarding with Stateful Switchover solution using OSPF.In the exhibit you can see the output of the show ip ospf neighbor detail command.Which trait of systems using Cisco Nonstop Forwarding with Stateful Switchover and OSPF is shown in the exhibit output and will impact your plan?（）
Refer to the exhibit. For the given configuration, on packets leaving the router on interface FastEthernet0/0 that matches the high traffic class, what will the MPLS experimental bit be set to?（）
In a high-availability network, which command, when placed on ports that have connected end stations, will allow you to prevent delays in service for end stations by placing a port in blocking mode?（）
Which command is used to view IPv6 parameters related to the BGP process?（）