Refer to the network of Layer 3 switches in the exhibit. The RPI Multi cast Server only multicasts to hosts connected to multilayer switches 5 and 6. The CMU Multicast Server multicasts to hosts on multilayer switches 1 - 6. Given the number of configuration steps involved, what is the most efficient way to configure the net work while meeting the requirements for multicast data flow? （）
A. Configure each switch with PIM sparse mode and a separate instance of PIM dense mode.Specify switch 1 as the root for the RPI Multicast Server. Specify switch 2 as the root for the CMU Multicast Server.
B. Configure each switch with PIM sparse mode and a separate instance of PIM dense mode. Leave each multicast server as the root of its own multicast tree.
C. Configure each switch with PIM sparse - dense mode. Configure switch 3 as a ren dezvous point for the RPI multicast stream.
D. Configure each switch with PIM sparse mode and a separate instance of PIM dense mode.Allow the switches to elect their own root for each multicast tree.
E. Configure each switch with PIM sparse mode.
F. Configure each switch with PIM dense mode.
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. All multilayer switches are running PIM dense mode. Recipient A and Recipient B are sending IGMPv2 joi n messages to their respective multilayer switches. Which statement is true?（）
A. The Multicast Server is the root of the multicast tree. Switches 1, 3, 4, and 5 will participate in the multicast tree once pruning has taken place.
B. The Multicast Serv er is the root of the multicast tree. Switches 4 and 5 will participate in the multicast tree once pruning has taken place.
C. Switch 3 is the root of the multicast tree. Switches 3,4, and 5 will participate in the multicast tree once pruning has taken place.
D. Switch 3 is the root of the multicast tree. Switches 1,3,4, and 5 will participate in the multicast tree once pruning has taken place.
E. Switch 1 is the root of the multicast tree. Switches 1,4, and 5 will participate in the multicast tree once pruning has taken place.
F. Switch 1 is the root of the multicast tree. Switches 1,3,4, and 5 will participate in the multicast tree once pruning has taken place.
A. PIM sparse - dense mode and PIM dense mode require an RP on the network.
B. PIM sparse mode and PIM dense mode require an RP on the network.
C. PIM sparse mode interfaces are always added to the multicast routing table in a router.
D. PIM sparse mode and PIM sparse - dense mode require an RP on the network.
E. PIM dense mode interfaces are always added to the multicast routing table in a router.
F. PIM sparse - dense mode acts as PIM dense mode if an RP is not known.
A. The multicast sources must register with the RP to form the multicast distribution tree.
B. An RP is required only in networks running Protocol Independent Multicast dense mode (PIM DM).
C. The multicast receivers must register with the RP to form the multicast distribution tree.
D. An RP is required only in networks running Protocol Independent Multicast sparse mode (PIM SM).
E. An RP is required only in networks running Protocol Independent Multicast sparse - dense mode (PIM - SDM).
F. To form the multicast distribution tree, the multicast sources register with and the receivers join the RP.
A. 228.10.10.7
B. 229.11.10.7
C. 229.138.10.7
D. 229.138.10.8
E. 228.10.10.8
F. 228.10.138.7
A. 169.254.23.59
B. 223.254.255.254
C. 225.1.1.1
D. 227.43.34.2
E. 238.3.3.3
F. 249.1.2.3
最新試題
Which of the following answers lists a multicast IPv6 address?（）
Which of the following are true of both OSPFv2 and OSPFv3?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?（）interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?（）
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?（）
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
Which of the following features work the same in both RIP- 2 and RIPng?（）