A. 228.10.10.7
B. 229.11.10.7
C. 229.138.10.7
D. 229.138.10.8
E. 228.10.10.8
F. 228.10.138.7
您可能感興趣的試卷
你可能感興趣的試題
A. 169.254.23.59
B. 223.254.255.254
C. 225.1.1.1
D. 227.43.34.2
E. 238.3.3.3
F. 249.1.2.3
A. acts as a meeting place for sources and receivers of multicast traffic
B. used in PIM dense m ode to create a database of all multicast sources
C. used in PIM dense and sparse mode to create a database of all multicast sources
D. acts as the designated router for a broadcast segment when multicast routing is enabled
Refer to the exhibit. IP multicast for group address 224.1.1.1 has been enabled on all router s in the network. Hosts on Network A receive the multicast traffic. However, hosts on Network B do not. On the basis of outputs provided, what could be the cause of the problem? ()
A. The route to 224.69.15.0/24 will be out Ethernet 0
B. The reverse path forwarding (RPF) for the route 224.2.0.1 failed to find the interface on which the multicast packet was rece ived
C. Multicast route to 224.69.15.0/24 was added to the mroute table and created by a source directly connected to the router
D. Multicast route to 10.16.0.0/16 was added to the mroute table and created by a source directly connected to the router
E. This router received an IGMP host report from a group member or a PIM join message
A. IGMP snooping and Cisco Group Membership Protocol (CGMP) can be used simultaneously on a switch.
B. IGMP snooping a nd Cisco Group Membership Protocol (CGMP) were developed to help Layer 3 switches make intelligent forwarding decisions on their own.
C. IGMP snooping examines IGMP join/leave messages so that multicast traffic is forwarded only to hosts that sent an IG MP message toward the router.
D. IGMP snooping is an IP multicast constraining mechanism for Layer 2 switches.
E. IGMP snooping is enabled with the ip multicast - routing global configuration command.
A. There are three IGMP modes: dense mode, sparse mode, and sparse - dense mode
B. IGMP is used to register individual hosts with a multicast group
C. IGMP version 3 enables a multicast receiving host to specify to the router which sources it should forward traffic from
D. IGMP messages a re IP datagrams with a protocol value of 2, destination address of 224.0.0.2, and a TTL value of 1
E. IGMP is a multicast routing protocol that makes packet - forwarding decisions independent of other routing protocols such as EIGRP
F. IGMP snooping ru ns on Layer 3 routers
最新試題
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?()Network Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?()
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?()
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?()
Which of the following features work the same in both RIP- 2 and RIPng?()
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?()
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?()ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Which of the following answers lists a multicast IPv6 address?()
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?()R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best