A. enbale password c1sco
B. secret enable c1sco
C. password enable c1sco
D. enable secret c1sco
您可能感興趣的試卷
你可能感興趣的試題
A. An IPv6 address is 64 b long and is represented as hexadecimal characters.
B. An IPv6 address is 32 b long and is represented as decimal digits.
C. An IPv6 address is 128 b long and is represented as decimal digits.
D. An IPv6 address is 128 b long and is represented as hexadecimal characters.
A. The new IOS image is too large for the router flash memory.
B. The TFTP server is unreachable from the router.
C. The new IOS image is not correct for this router platform.
D. The IOS image on the TFTP server is corrupt.
E. There is not enough disk space on the TFTP server for the IOS image.
This graphic shows the results of an attempt to open a Telnet connection to router ACCESS1 from router Remote27. Which of the following command sequences will correct this problem? （）
A. ACCESS1(config)# line console 0 ACCESS1(config-line)# password cisco
B. Remote27(config)# line console 0 Remote27(config-line)# login Remote27(config-line)# password cisco
C. ACCESS1(config)# line vty 0 4 ACCESS1(config-line)# login ACCESS1(config-line)# password cisco
D. Remote27(config)# line vty 0 4 Remote27(config-line)# login Remote27(config-line)# password cisco
E. ACCESS1(config)# enable password cisco
F. Remote27(config)# enable password cisco
A network administrator is troubleshooting the OSPF configuration of routers R1 and R2. The routers cannot establish an adjacency relationship on their common Ethernet link. The graphic shows the output of the show ip ospf interface e0 command for routers R1 and R2. Based on the information in the graphic, what is the cause of this problem?（）
A. The OSPF area is not configured properly.
B. The priority on R1 should be set higher.
C. The cost on R1 should be set higher.
D. The hello and dead timers are not configured properly.
E. A backup designated router needs to be added to the network.
F. The OSPF process ID numbers must match.
A. A remote physical layer problem exists.
B. The host NIC is not functioning.
C. TCP/IP has not been correctly installed on the host.
D. A local physical layer problem exists.
最新試題
Which cisco ios command can help to determine the timing of various debug events,relative to each other,when you are debugging a complicated router issue?（）
Which command is used to display the collection of OSPF link states?（）
Which statement is true, as relates to classful or classless routing?（）
A network administrator is planning a network installation for a large organization.The design requires 100 separate subnetworks,so the company has acquired a Class B network address.What subnet mask will provide the 100 subnetworks required, if 500 usable host addresses are required per subnet?（）
At which layer of the OSI model is RSTP used to prevent loops?（）
Three switches are connected to one anther via trunk ports.Assuming the default switch configuration,which switch is elected as the root bridge for the spanning-tree instance of vlan 1?（）
An employee of ABC company has move to an office on a different floor. Although the administrator is able to telnet to all of the routers,the address of Switch F is needed in order to verify that the employee remains in the same VLAN.Which action could be used by the administrator to find the IP address of Switch F?（）
If all OSPF routers in a single area are configured with the same priority value,what value dose a router use for the ODPF router ID in the absence of a loopback interface?（）
Which device might be installed at a branch office to enable and manage an IPsec site-to-site VPN?（）
Which name describes an IPV6 host-enable tunneling technique that uses IPV4 UDP,does not require dedicated gateway tunnels,and can pass through existing IPV4 NAT gateways?（）