An 802.1X client cannot authenticate to an autonomous access point configured for multiple
VLANs. The native VLAN does not have an SSID configured.
Which one of the following links being down would prevent the clients from authenticating？（）
A.between the RADIUS and the access point
B.between the client’s VLAN and the WLSE
C.between the native VLAN and the WLSE
D.between the client’s VLAN and the RADIUS
您可能感興趣的試卷
你可能感興趣的試題
In a deployment using the lightweight access points， clients set up to authenticate with EAP-PEAPor EAP-Cisco Wireless （LEAP） cannot authenticate. Upon inspection of the Failed Attempts reportyou see the following error： "Unknown network access server NAS."
What two problems can causethis type of failure？（）
A.misconfigured IP address of the AAA server on the wireless controller
B.misconfigured IP address of the wireless LAN controller on the AAA server
C.misconfigured EAP type on the wireless LAN controller
D.misconfigured shared secret on the wireless LAN controller
E.misconfigured EAP type on the AAA server
Your client has deployed a Cisco Wireless Location Appliance within their warehouse environment.They have been experiencing problems with tracking objects using active RFID tags. The RFID tagdata is not being collected.
On which device would you verify that RFID status has been enabled？（）
A.Cisco WCS
B.access point
C.wireless controller
D.location manager
A.802.11b/g
B.radio
C.access point
D.802.11a
A.IP
B.TCP
C.UDP
D.IPX
Your client has deployed a Cisco Wireless Location Appliance within their warehouse environment.They have been experiencing problems with tracking objects using active RFID tags. The RFID beacon rate is 10 seconds. You have discovered an issue with the RFID timeout value.
How shouldthis value be changed？（）
A.Change the value on the wireless controller to 45 seconds.
B.Change the value on the wireless controller to 95 seconds.
C.Change the value on the Cisco WCS to 95 seconds.
D.Change the value on the Cisco WCS to 45 seconds.
最新試題
Which protocol does the RADIUS server use inside the secure tunnel of EAP-FAST to authenticatethe client when one-time passwords are in use？（）
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter，the status LED and activity LED are alternating on and off.What does this indicate？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
The Cisco Wireless Location Appliance provides an audit trail for each device tracked for up to how many days？（）
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor，4GB RAM， and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem？（）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）
You are charges with implementing a secure wireless installation which will provide Internet accessto client devices but will not allow communications between wireless clients.In addition to implementing PSPF or peer-to-peer blocking on the wireless side，which of the following actionsshould you perform on the wired infrastructure？（）
You have been called upon to add location-based services into an existing controller-basedwireless design which primarily encompasses handheld devices such as barcode scanners and Cisco7920 wireless IP phones.In which mode should you deploy the additional access points to achievethe density required without excessive co-channel interference？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone on a standalone WLAN.The phone rings but， when you answer， the call is dropped.What may cause this problem？（）
If it is properly deployed， a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller？（）