Using the WLSE， you are trying to push out a configuration job to a standalone access point， but the jobdoes not start.
Which of the following would cause this failure？（）
A.invalid parameter in the template
B.pop-up blocker enabled in the browser
C.incorrect SNMP communities on the access point
D.unsupported version of IOS firmware in the access point
您可能感興趣的試卷
你可能感興趣的試題
You are charged with implementing a secure wireless installation which will provide Internet access to clientdevices but will not allow communications between wireless clients. In addition to implementing PSPF orpeer-to-peer blocking on the wireless side.
Which of the following actions should you perform on the wiredinfrastructure？（）
A.Take no action， you have achieved your goal.
B.Implement a Cisco Secure IPS sensor.
C.Implement a protected port on the access switches.
D.Implement 802.1X on the switch ports.
A Cisco 4404 WLAN controller is being connected to a Cisco 6500 Catalyst Series Switch.
How would younterconnect and configure LAG for connectivity and ensure redundancy？（）
A.All four ports from the Cisco WLC terminated to the same Catalyst gigabit module and channel group.
B.All four ports from the Cisco WLC terminated to the same Catalyst gigabit module using two channel groups.
C.Ports 1 and 2 from Cisco WLC to Catalyst gigabit module slot 1 channel group 20 and Cisco WLC ports3 and 4 to Catalyst gigabit module slot 2 channel group 40.
D.Ports 1 and 2 from Cisco WLC to Catalyst gigabit module slot 1 channel group 10 and Cisco WLC ports3 and 4 to Catalyst gigabit module slot 2 channel group 10.
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A client that isanchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run a debug command on the 4402 controller.
Which message would best describe the establishment of the tunnel fromthe foreign controller’s perspective？（）
A.Transmit Mobile Anchor Export message
B.Received Mobile Anchor Export message
C.Transmit Plumbing duplex mobility tunnel message
D.Received Plumbing duplex mobility tunnel message
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication.
In order toaccomplish this，which two IETF RADIUS attributes should you configure on the Cisco Secure ACS？（）
A.064 Tunnel-Type
B.066 Tunnel-Client-Endpoint
C.067 Tunnel-Server-Endpoint
D.081 Tunnel-Private-Group-ID
E.082 Tunnel-Assignment-ID
You have been called upon to add location-based services into an existing controller-based wireless designwhich primarily encompasses handheld devices such as barcode scanners and Cisco 7920 wireless IPphones.
In which mode should you deploy the additional access points to achieve the density required without excessive co-channel interference？（）
A.sniffer mode
B.monitor mode
C.location mode
D.tracking mode
最新試題
If it is properly deployed， a controller-based access point is capable of monitoring all VLANs on anetwork when you select which of the following modes from the AP Mode drop-down menu onthe controller？（）
A Cisco Wireless Location Appliance has been added to track RFID tags placed on laptops beingused in a school.Classrooms at the school have concrete block walls. During testing，you discoverthat the accuracy of the system needs to be improved.You decide to edit the map in the Cisco WCS to add the interior walls.How many interior walls can you add to improve the accuracy of thelocation appliance？（）
You are trying to change the polling parameters used by the location manager via the Cisco WCS，and your request is being denied. What is wrong？（）
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
Which of the following parameter sets must be configured on the Cisco Wireless Location Appliance？（）
You are configuring a wireless LAN controller for QoS.Which 802.11e user priority tag should you apply to voice applications？（）
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
You are using ADU and are authenticated and associated to an access point. However， you are unable to obtain an IP address.Which of these has caused this problem？（）
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is， you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to？（）