You are using ADU and are authenticated and associated to an access point. However, you are unable toobtain an IP address.
Which of these has caused this problem?()
A.invalid SSID
B.invalid 802.1X authentication type
C.invalid encryption type
D.invalid WEP key
您可能感興趣的試卷
你可能感興趣的試題
Your customer has deployed a Cisco Wireless Location Appliance within its warehouse environment.However, employees there have been experiencing problems when tracking objects using active RFIDtags. You use an access point scan to determine if the Location Appliance has been deployed correctly.
Making which change to warehouse deployment location services will most likely correct the problem?()
A.allow for the automatic containment of rogue access points
B.ensure each area is covered by a minimum of three access points
C.ensure channels are deployed such that they do not overlap
D.ensure a minimum RSSI value of -50
On a Cisco 1000 Series controller-based access point, the alarm LED is flashing red, but the other LEDsare off.
What is this access point indicating?()
A.It has lost contact with the controller.
B.It requires a code upgrade.
C.It is operating normally.
D.Its IP address already exists.
On a standalone access point, client association using EAP-Cisco Wireless (Cisco-LEAP) is failing, butassociation using EAP-PEAP is functioning.
What needs to be enabled on the standalone access point tocorrect this issue?()
A.a shared key
B.network EAP
C.open authentication plus EAP
D.open authentication plus MAC
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2. H-REAP AP2 has six other clients associated to it, which continue to pass traffic.
What has caused this problem?()
A.H-REAP AP1 lost its connection to the controller.
B.H-REAP AP2 lost its connection to the controller.
C.H-REAP AP1 has reached its client limit.
D.H-REAP AP2 has reached its client limit.
A Cisco Aironet 1020 controller-based access point has been connected to a Catalyst 3550-24 PWRSwitch. However, when it is powered up, the access point fails.
What has caused this problem?()
A.access point has not been initialized with the primary controller
B.switch port is not enabled
C.switch does not support 802.3af
D.access point does not support 802.11h
E.incorrect switch power supply
最新試題
What is the maximum number of wireless controllers that the highest-end Cisco WCS server canmanage?()
You are troubleshooting a problem with a Cisco 7920 wireless IP phone that is causing the phoneto drop calls. The problem appears to be roaming bandwidth issue. In order to verify what kind ofissue it is, you decide to increase the bandwidth reserve for roaming on the WLAN controller tomaximum.What level do you set the bandwidth to?()
When configuring a WLAN controller for a voice application using Cisco 7920 wireless IP phones,which two general control settings should you select?()
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add?()
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter,the status LED and activity LED are alternating on and off.What does this indicate?()
A Cisco WCS version 4.0 has been installed on a server with a dual Pentium 3.0 GHz processor,4GB RAM, and an 80 GB hard drive. A location appliance has been incorporated into the networkand is being monitored by the Cisco WCS. There are 3000 devices to be tracked but not all of themare being tracked on the Cisco WCS.What can be done to correct the problem?()
You are troubleshooting a one-way call problem with a Cisco 7920 wireless IP phone on a standalone WLAN.What may cause this problem?()
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode?()
Clients using Cisco-LEAP and EAP-FAST authentication are having no problems logging on to thewireless network, but clients using PEAP are failing to log on.Which situation would result in thistype of problem?()
On a Cisco Aironet 1240AG Series standalone access point, the radio LED is dark blue and blinking,but the status LED and Ethernet LED are both off.What does this indicate?()