A.15
B.10
C.1
D.5
您可能感興趣的試卷
你可能感興趣的試題
A mobility group is created by a Cisco WLCM and 4402 Series Wireless LAN Controller. A clientthat is anchored on the Cisco WLCM roams to an access point on the 4402 controller. You then run adebug command on the 4402 controller.
Which message would best describe the establishment of the tunnel from the foreign controller’sperspective？（）
A.Received Mobile Anchor Export message
B.Transmit Plumbing duplex mobility tunnel message
C.Received Plumbing duplex mobility tunnel message
D.Transmit Mobile Anchor Export message
You are charged with implementing a secure wireless installation which will provide Internet
access to client devices but will not allow communications between wireless clients. In addition toimplementing PSPF or peer-to-peer blocking on the wireless side.
Which of the following actionsshould you perform on the wired infrastructure？（）
A.Implement a Cisco Secure IPS sensor.
B.Implement 802.1X on the switch ports.
C.Take no action， you have achieved your goal.
D.Implement a protected port on the access switches.
You want to dynamically assign users to an 802.1Q VLAN as a result of their authentication. Inorder to accomplish this.
Which two IETF RADIUS attributes should you configure on the Cisco SecureACS？（）
A.083 Tunnel-Preference
B.066 Tunnel-Client-Endpoint
C.064 Tunnel-Type
D.082 Tunnel-Assignment-ID
E.081 Tunnel-Private-Group-ID
F.067 Tunnel-Server-Endpoint
On a Cisco Aironet 1240AG Series standalone access point， the radio LED is dark blue andblinking，but the status LED and Ethernet LED are both off.
What does this indicate（）？
A.A firmware upgrade is in progress.
B.An access point buffer overflow is occurring.
C.The access point is booting.
D.The internal radio has failed.
A.router（config-ssid）# enable
B.router（config-ssid）# advertise
C.router（config-ssid）# broadcast
D.router（config-ssid）# guest-mode
最新試題
On a Cisco Aironet 802.11 a/b/g wireless LAN client adapter，the status LED and activity LED are alternating on and off.What does this indicate？（）
Which of the following accurately represents the functionality of a lightweight access point configured to operate in sniffer AP mode？（）
You have a very few Cisco 7920 wireless IP phones on your network， but lots of wireless laptops.You want to increase the bandwidth available for the laptops by decreasing the bandwidth reserved for the Cisco 7920 phones.What is the lowest percentage of voice-allocated bandwidthyou can select on the WLAN controller？（）
You have just finished aligning a Cisco Aironet 1400 Series Wireless Bridge link using installationmode. When you set the link back to operational mode you loose association to the root bridge.Which action will correct the problem？（）
When configuring Cisco Secure ACS to support wireless EAP authentication， which device must be configured as a AAA client？（）
You are configuring an RF group of controllers that coordinate Radio Resource Management calculations.What is the maximum number of WLAN controllers that you can add？（）
You are installing a Cisco Aironet 1000 Series controller-based access point. When you boot it， allthe LEDs on the access point blink together.What does this indicate about the access point？（）
You are trying to change the polling parameters used by the location manager via the Cisco WCS，and your request is being denied. What is wrong？（）
On a WLAN controller， what is the default roaming bandwidth percentage reserved for voice clients？（）
A client roams from H-REAP AP1 to H-REAP AP2. The client is unable to associate to H-REAP AP2.H-REAP AP2 has six other clients associated to it， which continue to pass traffic.What has causedthis problem？（）