A. CIS 1# show class-map forward Class map match-all forward ( id 3) Match ip dscp 18
B. CIS1#show access-map block Class map match-all block (id 4) Match ip dscp 43
C. CIS1# show class-map real-time Class map match-all block (id 5) Match ip dscp 16
D. CIS 1# show class-map pass Class map match-all real-time (id 2) Match ip dscp 40
您可能感興趣的試卷
你可能感興趣的試題
You are an experienced network administrator in an international company. During your working hours, customers complain that they experience intermittent data loss and they intermittently fail to connect to crucial servers. As shown in the following topology, the 802.1Q trunk between DSW111 and ASW1 fails. Though DSW112 is in the service of HSRP group 11, the SVI for VLAN 11 is up on DSW111.
So as to figure out the problem,
which three commands should you issue on DSW111? （）(Choose three.)
A. show standby vlan 11 brief
B. show interfaces vlan 11
C. show spanning-tree vlan 11
D. show interfaces
You are troubleshooting an issue which is causing full-sized packets entering the MPLS cloud be dropped. You have discovered that one of the switches in the MPLS core is not a Cisco switch, but otherwise the MPLS MTU size is set to 1508 bytes on the routers.
Based on this information, which of these may be the reason the packets are being dropped?（）
A. The switch on you MPLS core that was not produced by Cisco does not support oversized packets
B. No switches support oversized packets
C. By definition, the maximum MTU is 1500 bytes
D. As MPLS VPN labeling increases the size of the packet by 8 bytes, the IP MTU should have been changed to 1508
A. Layer 2 TTL
B. Layer 3 TTL
C. Layer 3 source address
D. Layer 3 destination address
A. Show module
B. Show errdisable detect
C. Show environment
D. Show diagnostic content
A Catalyst switch has just been installed and configured, and is not working as expected. You have decided to capture multiple show command outputs to study.
Which one command could you use that includes the output of many other show commands, such as show version and show running-config?（）
A. show configuration
B. show memory
C. show stacks
D. show tech-support
最新試題
What are four advantages to using tunnel brokers in an IPv6 transition environment?（）
Which keyword is used with the debug ipv6 [keyword] command to troubleshoot neighbor discovery problems?（）
Which configuration will enable OSPF for IPv6 on FastEthernet 0/0/0?（）
Which command displays only those entries in a BGP table with specific AS_PATH attributes?（）
As a network administrator, you issue the interface auto qos voip cisco-phone command on a port in an edge network. It is possible for a Cisco Catalyst switch to check if a Cisco IP Phone is directly attached to that port by:（）
What is the purpose of using VPN hardware acceleration equipment?（）
Which Cisco IOS command is used to troubleshoot a problem in which a BGP session stays in the active state?（）
Referring to the partial Cisco Catalyst switch configuration shown, which two of these statements are correct? （）(Choose two.)
What is the maximum number of Cisco Catalyst 3750 Series Switches that can be united into a single manageable unit using the Cisco StackWise technology?（）
Refer to the exhibit. You want to minimize the downtime that results from supervisor engine switchovers on Cisco 6500 Series Switches and Cisco 7600 Series Routers. To achieve this, you are considering deploying a Cisco Nonstop Forwarding with Stateful Switchover solution using OSPF.In the exhibit you can see the output of the show ip ospf neighbor detail command.Which trait of systems using Cisco Nonstop Forwarding with Stateful Switchover and OSPF is shown in the exhibit output and will impact your plan?（）