Refer to the exhibit. You want to minimize the downtime that results from supervisor engine switchovers on Cisco 6500 Series Switches and Cisco 7600 Series Routers. To achieve this, you are considering deploying a Cisco Nonstop Forwarding with Stateful Switchover solution using OSPF.
In the exhibit you can see the output of the show ip ospf neighbor detail command.
Which trait of systems using Cisco Nonstop Forwarding with Stateful Switchover and OSPF is shown in the exhibit output and will impact your plan?（）
A. Stateful Switchover for Cisco Nonstop Forwarding only works with BGP.
B. Stateful Switchover for Cisco Nonstop Forwarding must be configured on all adjacent routers.
C. Cisco Nonstop Forwarding with Stateful Switchover helper mode is not supported on the adjacent router.
D. Cisco Nonstop Forwarding with Stateful Switchover helper mode for OSPF has been promiscuousstandardized and is supported on the adjacent router.
您可能感興趣的試卷
你可能感興趣的試題
A. An information trap is sent to the SNMP server.
B. Informational and debug messages are logged to the syslog server.
C. All messages are sent to the logging host, where selections are made.
D. All messages from emergencies to informational are sent to the logging host.
A. When a router receives a failure response, it stops querying authentication methods.
B. When a router receives an error response, it stops querying authentication methods.
C. If the router receives a failure response from an authentication method, it queries the next method.
D. The router does not differentiate between failure and error responses; the authentication process is always interrupted.
E. If it receives no response from the authentication method, a router will determine the error condition on its own; the router also has the option to proceed to the next method in a list if configured accordingly.
A. It is achieved by using more than one HSRP group.
B. It is done in regards to either round robin or weight basis.
C. It is used to offload the active router in a certain HSRP group.
D. Single group HSRP is used to achieve more efficient link utilization.
E. The return traffic is influenced by HSRP load sharing configuration.
A. RIP does not support routing contexts
B. routing contexts are implemented in a single routing process
C. routing contexts are implemented using multiple routing processes
D. routing contexts are implemented as several instances of a single routing process
E. routing contexts are implemented as a single instance of several routing processes
A. start LDP
B. enable CEF switching
C. configure the MPLS ID
D. disable IP TTL propagation
E. configure conditional label advertising
F. enable label switching on frame mode interfaces
最新試題
Which keyword is used with the show ip bgp neighbors [keyword] command to display all routes that are received and accepted from a neighbor?（）
Refer to the exhibit. For the given configuration, on packets leaving the router on interface FastEthernet0/0 that matches the high traffic class, what will the MPLS experimental bit be set to?（）
What is the purpose of using VPN hardware acceleration equipment?（）
What is the most likely reason that an IBGP route that has been selected as a best route is not entered into the IP routing table?（）
Refer to the exhibit. You have a non-Cisco switch that is not communicating properly while connected to the distribution-layer Cisco switching fabric.Which two best-practice actions can you take to overcome this problem? （）(Choose two.)
You are an experienced network administrator in an international corporation. During your working hours, you are asked to deploy the Cisco SSL VPN AIM module in a Cisco 1800 Series Router. The beneficial reason for that deployment is to:（）
Refer to the exhibit. You want to minimize the downtime that results from supervisor engine switchovers on Cisco 6500 Series Switches and Cisco 7600 Series Routers. To achieve this, you are considering deploying a Cisco Nonstop Forwarding with Stateful Switchover solution using OSPF.In the exhibit you can see the output of the show ip ospf neighbor detail command.Which trait of systems using Cisco Nonstop Forwarding with Stateful Switchover and OSPF is shown in the exhibit output and will impact your plan?（）
When a Cisco router is configured for SSH, it acts as an （）?
What is the function of the no switchport catalyst switch interface configuration command?（）
Refer to the exhibit. You want to minimize the downtime that results from supervisor engine switchovers on Cisco 6500 Series Switches and Cisco 7600 Series Routers. To achieve this, you are considering deploying a Cisco Nonstop Forwarding with Stateful Switchover solution using OSPF.In the exhibit you can see the output of the show ip ospf neighbor detail command.Which trait of systems using Cisco Nonstop Forwarding with Stateful Switchover and OSPF is shown in the exhibit output and will impact your plan?（）