A. facilitates customer deployments that are less reliable
B. facilitates customer deployments that are more predictable
C. separates products and technologies into individual portfolios
D. incorporates products and technologies into a broad portfol
E. strives to protect access to design documentation
您可能感興趣的試卷
你可能感興趣的試題
A. to make CEF tables smaller
B. to enable label switching on the frame mode interface
C. to restrict MPLS availability to predefined time periods
D. to restrict label switching to a limited number of networks
E. to restrict end users from seeing the routers in the MPLS network
Refer to the exhibit. This shows the NetFlow statistics for a router. You are analyzing the traffic pattern and you are interested in the percentage of packets between 32 and 64 bytes in size and the number of flows in progress. Which of these identifies both numbers correctly?（）
A. 69.4%, 4061
B. 24.9%, 980
C. 69.4%, 35
D. 6.94%, 980
E. cannot be determined from this output
A. When a router receives a failure response, it stops querying authentication methods.
B. When a router receives an error response, it stops querying authentication methods.
C. If the router receives a failure response from an authentication method, it queries the next method.
D. The router does not differentiate between failure and error responses; the authentication process is always interrupted.
E. If it receives no response from the authentication method, a router will determine the error condition on its own; the router also has the option to proceed to the next method in a list if configured accordingly.
Refer to the exhibit. MPLS has been enabled on router PE11. Which of these statements is correct regarding the output display shown in the exhibit? （）
A. CEF switching is not needed for MPLS operation.
B. CEF switching is only needed to forward labeled packets.
C. CEF switching is needed on both ingress and egress interfaces on which MPLS is enabled.
D. Interface-level CEF switching is needed only on egress interfaces that are sending IP packets on which the egress LSR performs the label imposition process.
E. Interface-level CEF switching is needed only on ingress interfaces that are receiving IP packets on which the ingress LSR performs the label imposition process.
A. syslog logging
B. terminal logging
C. buffered logging
D. console logging
最新試題
What is the most likely reason that an IBGP route that has been selected as a best route is not entered into the IP routing table?（）
Which configuration will enable OSPF for IPv6 on FastEthernet 0/0/0?（）
When a Cisco router is configured for SSH, it acts as an （）?
Refer to the exhibit. You want to minimize the downtime that results from supervisor engine switchovers on Cisco 6500 Series Switches and Cisco 7600 Series Routers. To achieve this, you are considering deploying a Cisco Nonstop Forwarding with Stateful Switchover solution using OSPF.In the exhibit you can see the output of the show ip ospf neighbor detail command.Which trait of systems using Cisco Nonstop Forwarding with Stateful Switchover and OSPF is shown in the exhibit output and will impact your plan?（）
As an experienced network engineer, you are asked to troubleshoot a CIS network outage. During the troubleshooting process, you notice that one of your colleagues connects additional devices to the network with the use of his own switch. With the purpose of improving speed, the switch is attached to both network ports in an office, which leads to bridge loop.Enabling which of the following feature will be able to prevent this problem from happening again?（）
Refer to the exhibit. For the given configuration, on packets leaving the router on interface FastEthernet0/0 that matches the high traffic class, what will the MPLS experimental bit be set to?（）
You are trying to initiate an SSH connection to a remote router and are getting rejected with an error code of 0. Which of these might be the cause of the error?（）
Which Cisco IOS command is used to troubleshoot a problem in which a BGP session stays in the active state?（）
Which description is making sense on the basis of the given information?（）
Which command is used to view IPv6 parameters related to the BGP process?（）