A. The router must have one routing protocol configured, but configuration for both routing protocols is not necessary
B. The router must hav e at least one working link connected to each routing domain
C. The redistribute command must be configured under EIGRP to send the routes to OSPF
D. The redistribute command should be configured under OSPF to take routes from EIGRP into OSPF
您可能感興趣的試卷
你可能感興趣的試題
A. To exchange routes between merged companies
B. To give separate control over routing to different parts of one company
C. To support multiple router vendors
D. To knit together an OSPF area if the area becomes discontiguous
Ten routers, R1 through R10, connect in a partial mesh over Frame Relay. For the mesh, R1 and R2 have PVCs connected to all other routers, but Routers R3 through R10 act as branch routers, with only two PVCs - one to R1 and one to R2. The routers u se IP subnet 10.1.1.0/24, with addresses 10.1.1.1, 10.1.1.2, and so on, through 10.1.1.10, respectively. The routers all use Inverse ARP to learn Frame Relay mapping information. All routers use a multipoint subinterface with network type point - tomultip oint nonbroadcast. A co - worker's implementation plan lists lots of configuration commands related to this design. The design states that all hosts should be able to ping all other hosts.
Which commands are required for proper functioning of OSPF in this case?（）
A. frame - relay map commands on R3 - R10 referencing the other routers in this group
B. Nine OSPF neighbor commands on each router
C. Nine OSPF neighbor commands on R1 and R2, with only two such commands on R3 - R10
D. R1 and R2 with ip ospf prio rity 1 commands to ensure they become DR and BDR
E. R3 - R10 with ip ospf priority 0 commands to ensure they do not become DR or BDR
Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface.
What command would make this router not use a DR, and dynamically discover OSPF neighbors?（）
A. ip ospf network broadcast
B. ip ospf network non - broadcast
C. ip ospf network point - to - multipoint
D. ip ospf network point - to - multipoint non - broadcast
Router R1 connects to a Frame Relay cloud using a multipoint subinterface, with ten PVCs associated with the subinterface.
What command would make this router not use a DR and require static OSPF neighbor definition?（）
A. ip ospf network broadcast
B. ip ospf netw ork non - broadcast
C. ip ospf network point - to - multipoint
D. ip ospf network point - to - multipoint non - broadcast
Several links have been broken so th at for the next day or two, what was formerly a contiguous area 0 has been broken into two parts. However, both parts of area 0 have working links into area 1 using routers with RID 1.1.1.1 and 2.2.2.2.
Which answers list the command on the router with RID 1.1.1.1 to create a virtual link to help solve this temporary problem?（）
A. area 0 virtual - link 2.2.2.2
B. area 1 virtual - link 2.2.2.2
C. area 0 source - rid 1.1.1.1 dest - rid 2.2.2.2
D. virtual - link transit - area 1 RID 2.2.2.2
最新試題
An ISP has assigned prefix 3000:1234:5678::/48 to Company1. Which of the following terms would typically be used to describe this type of public IPv6 prefix?（）
Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE.Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?（）
Which of the following must match for two directly connected routers running OSPF to establish a neighbor adjacency?（）
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
Which of the following answers lists a multicast IPv6 address?（）
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
Which of the following features work the same in both RIP- 2 and RIPng?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable