A network design shows that R1 has four different possible paths from itself to the Data Center subnets.
Which one of the following commands is most likely to show you all the possible next - hop IP addresses for these four possible routes?（）
A. show ip eigrp topology
B. show ip eigrp topology all - links
C. show ip route eigrp
D. show ip route eigrp all - links
E. show ip eigrp topology all - learned
您可能感興趣的試卷
你可能感興趣的試題
A company has a Frame Relay WAN with one central - site router and 100 branch office routers. A partial mesh of PVCs exists: one PVC between the central site and each of the 100 branch routers.
Which of the following could be true about the number of EIGRP neighbor ships?（）
A. A partial mesh totaling 100: one between the central - site router and each of the 100 branches.
B. A full mesh - (101 * 100) / 2 = 5050 - One neighborship between each pair of routers.
C. 101 - One between each router (including the central site) a nd its nearby PE router.
D. None of the answers is correct.
Refer to the exhibit. Which two statements are true about the partial configuration that is shown? （）
A. The first DHCP client to connect to the FastEthernet 0/1 interface will receive the IP address 10.10.0.1.
B. DHCP requests received on the FastEthernet 0/1 interface will be forwarded to 10.0.0.2.
C. The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP a ddress 10.0.0.1
D. The first DHCP client to connect to the FastEthernet 0/0 interface will receive the IP address 10.0.0.6.
E. Hosts connected to the FastEthernet0/1 interface will not receive DHCP replies from the router.
A. BOOTP
B. TFTP
C. ARP
D. DNS
E. proxy - ARP
F. FTP
Refer to the exhibit. Routers R1 and R2 have established a neighbor relationship and are exchanging routing information. The network design requires that R1 r eceive routing updates from R2, but not advertise any routes to R2. Which configuration command sequence will successfully accomplish this task? （）
A. R1(config)# router eigrp 1 R1(config - router)# passive - interface serial 0
B. R1(config)# access - list 2 0 deny any R1(config)# router eigrp 1 R1(config - router)# distribute - list 20 out serial 0
C. R2(config)# access - list 20 permit any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 in serial 0
D. R1(config)# access - list 20 permit any R 1(config)# router eigrp 1 R1(config - router)# distribute - list 20 in serial 0
E. R2(config)# access - list 20 deny any R2(config)# router eigrp 1 R2(config - router)# distribute - list 20 out serial 0
F. R2(config)# router eigrp 1 R2(config - router)# passive - interface serial 0
A. all interfaces in the path toward the destination
B. all networks in the path toward the destination
C. adjacent next hop router in the path toward the destination
D. all routers in the path toward the destination
E. all interfaces through which the packets can be routed
F. type of service and precedence in the IP packets
最新試題
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?（）D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?（）ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?（）interface f0/0ipv6 address 2345:0:0:8::1/64
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
Which of the following answers lists a multicast IPv6 address?（）
Which of the following are true of both OSPFv2 and OSPFv3?（）