The following exhibit shows ipv6 route output. What would the metric be fo r a summary route that summarizes all three OSPFv3 routes displayed?()
A. 160
B. 140
C. 120
D. 100
您可能感興趣的試卷
你可能感興趣的試題
A. Only the path that is the feasible successor should be used.
B. Load balancing is disabled on t his router.
C. The router only performs equal - cost load balancing on all paths that have a metric greater than 1
D. The router performs equal - cost load balancing.
Refer to the exhibit. On the basis of the partial configuration, which two statements are correct? ()
A. Only routes 10.0.1.0/24 will be sent out all interfaces.
B. Only routes matching 10.0.0.0/8 will be advertised out interfaces other than Ethernet 0.
C. Only routes matching 10.0.0.0/8 will be advertised out Ethernet 0.
D. Only routes matching 10.0.1.0/24 will be advertised out Ethernet 0.
E. Only routes 10.0.1.0/24 will be allowed in the routing table.
F. All rout es will be advertised out interfaces other than Ethernet 0.
A. many - to - one
B. one - to - one
C. one - to - many
D. many - to - many
A. After the router ospf 10 and passive - interface s0/0 commands have been issued , the s0/0 interface will not send any OSPF updates, but will receive routing updates on that interface
B. When you use the passive - interface command with RIPv2, multicasts are sent out the specified interface
C. After the router rip and passive -interface s0/0 commands have been issued, the s0/0 interface will not send any RIP updates, but will receive routing updates on that interface
D. When you use the passive - interface command with EIGRP, hel lo messages are not sent out the specified interface
E. After the router eigrp 10 and passive - interface s0/0 commands have been issued, the s0/0 interface will not send any EIGRP updates, but will receive routing updates on that interface
F. When you use the passive - interface command with OSPF, hello messages are not sent out the specified interface
Refer to the exhibit. What must be done on router RTA to ensure that EIGRP works effectively in a Frame Relay multipoint environment?()
A. Issue the command bandwidth 224 on the physical interface.
B. Issue the command bandwidth 56 on the physical interface.
C. Issue the command bandwidth 224 on each subinterface.
D. Issue the command bandwidth 56 on each subinterface.
最新試題
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?()
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?()
The following configura tion exists on a router on one end of an IPv6 tunnel. Which type of tunnel is created by this configuration?()interface loopback 1ip address 1.1.1.1 255.255.255.255interface tunnel 2ipv6 address 2000::1::/64tunnel source loopback 1tunnel destina tion 2.2.2.2tunnel mode ipv6ipipv6 eigrp 1
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?()
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?()
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer?()interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?()
The following output occurs on Router R1 , which runs both EIGRP for IPv6 and OSPFv3, with redistribution from EIGRP into OSPF configured with the redistribute eigrp 1 metric 25 command. Interface S0/0/1 has been enabled for EIGRP ASN 1. Which of the following should be true of redistribution in this case?()D 2000::/64 [90/1422516]via FE80::213:19FF:FE7B:5026, Serial0/0/1C 2000:0:0:1::/64 [0/0]via Serial0/0/1, directly connectedL 2000::1:213:19FF:FE7B:5004/128 [0/0]via Serial0/0/1, receive
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?()ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?()ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0