Refer to the exhibit.
Which statement is true about the display of the command show pagp 1 neighbor command？（）
A.STP packets are sent out the Gi0/1 interface only.
B.STP packets are sent out both the Gi0/1 and Gi0/2 interfaces.
C.CDP packets are sent out the Gi0/1 interface only.
D.CDP packets are sent out the Gi0/2 interface only.
您可能感興趣的試卷
你可能感興趣的試題
A.allows an UDLD port to automatically reset when it has been shutdown
B.resets all UDLD enabled ports that have been shutdown
C.removes all UDLD configurations from interfaces that were globally enabled
D.removes all UDLD configurations from interfaces that were enabled per-port
Refer to the exhibit. When a profile is configured in the Aironet Desktop Utility，
which security option permits the configuration of host-based Extensible Authentication Protocol （EAP）？（）
A.WPA/WPA2/CCKM
B.WPA/WPA2 Passphrase
C.802.1x
D.Pre-Shared Key （Static WEP）
Network topology exhibit：
Interface VLAN 101 exhibit：
Interface VLAN 102 exhibit：
Interface VLAN 104 exhibit：
Interface VLAN 105 exhibit：
You work as a network technician at. You study the network topology and the other exhibits carefully. Consider the distribution switches 1 and 2. 1 is the primary device for Vlan 101， 102， 105. 2 is the primary device for Vlan 103 and 104
Note： Please refer to the #2 scenario.
During routine maintenance， it became necessary to shutdown G1/0/1 on1 and2.
All other interface were up. During this time，1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group.
What can be done to make the group function properly ？（）
A.On 1， disable preempt
B.On 2， decrease the priority value to a value less than 150
C.On 1， increase the decrement value in the track command to a value greater than 6
D.On 1， disable track command.
Network topology exhibit：
Interface VLAN 101 exhibit：
Interface VLAN 102 exhibit：
Interface VLAN 104 exhibit：
Interface VLAN 105 exhibit：
You work as a network technician at. You study the network topology and the other exhibits carefully. Consider the distribution switches1 and 2. 1 is the primary device for Vlan 101， 102， 105. 2 is the primary device for Vlan 103 and 104
Note： Please refer to the #2 scenario.
2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group.
What can be done to make the group function properly ？（）
A.On 1， disable preempt
B.On 1， decrease the priority value to a value less than 190 and greater than 150
C.On 2， increase the priority value to a value greater 241 and less than 249
D.On 2， increase the decrement value in the track command to a value greater than 10 and less than 50.
Switch 1 was configured as shown below：
Based on the output shown above，
which statement is true？（）
A.IP traffic matching access list is forwarded through VLANs 5-10.
B.All VLAN traffic in VLANs 5-10 that match access list will be forwarded， and all else will be dropped.
C.IP traffic matching VLAN list 5-10 will be forwarded， and all other traffic will be dropped.
D.All VLAN traffic matching VLAN list 5-10 will be forwarded， and all traffic matching access list is dropped.
E.None of the other alternatives apply
最新試題
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
What two things will occur when an edge port receives a BPDU？（）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
Refer to the exhibit. For what purpose is the command show ip cef used？（）
Which statement is correct about RSTP port roles？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）