A.detailed list of personnel assigned to each task within the plan
B.a Layer 2 spanning tree design topology
C.rollback guidelines
D.placing all unused access ports in VLAN 1 to proactively manage port security
E.enabling SNMP access to Cisco Discovery Protocol data for logging and forensic analysis
您可能感興趣的試卷
你可能感興趣的試題
A.detailed VLAN information
B.an incident response plan
C.results of testing the new network configuration
D.an existing hierarchical network topology
E.a security policy for your organization
You are tasked with designing a security solution for your network.
What information should be gathered prior to designing the solution？（）
A.a list of applications currently in use in the network
B.IP addressing design plans so that the network can be appropriately segmented to mitigate potential network threats
C.detailed security device specifications
D.results from pilot network testing
You are tasked with designing a security solution for your network.
What information should be gathered prior to designing the solution？（）
A.IP addressing design plans so that the network can be appropriately segmented to mitigate potential network threats
B.detailed security device specifications
C.results from pilot network testing
D.results from a network audit
You are tasked with designing a security solution for your network.
What information should be gathered prior to designing the solution？（）
A.IP addressing design plans so that the network can be appropriately segmented to mitigate potential network threats
B.a list of the customer requirements
C.detailed security device specifications
D.results from pilot network testing
Cat6500（config）# router ospf 1
Cat6500（config-router）# network 0.0.0.0 255.255.255.255 area 0
Cat6500（config-router）# nsf Cat6500（config-router）#end
Refer to the exhibit. The configuration is used to enable nonstop forwarding for OSPF on a Catalyst 6500 Series
Switch with redundant supervisor engines.
The default CEF configuration is unchanged. After testing， user traffic is interrupted and NSF is not operational.
What is the most likely reason？ （）
A.CEF was not properly configured.
B.OSPF was not properly configured for graceful restart.
C.Stateful switchover was not correctly configured.
D.NSF for OSPF is only supported in area 0.
最新試題
Refer to the exhibit. Switch S2 contains the default configuration. Switches S1 and S3 both have had the command spanning-tree mode rapid-pvst issued on them. What will be the result？（）
Refer to the exhibit. Switch 15 is configured as the root switch for VLAN 10 but not for VLAN 20. If the STP configuration is correct， what will be true about Switch 15？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit. All network links are FastEthernet. Although there is complete connectivity throughout the network， Front Line users have been complaining that they experience slower network performance when accessing the server farm than the Reception office experiences. Based on the exhibit， which two statements are true？（）
Examine the diagram. A network administrator has recently installed the above switched network using 3550s and would like to control the selection of the root bridge.Which switch should theadministrator configure as the root bridge and which configuration command must theadministrator enter to accomplish this？（）
What two things will occur when an edge port receives a BPDU？（）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Which three statements about STP timers are true？（）