欧美国产精品一级二级三级,国产a特一级毛片

多項選擇題The maximum number of routers per OSPF area typically depends on which three factors?（）

A. the kind of OSPF areas being implemented
B. the number of external LSAs in the network
C. the number of DRs and BDRs in the areas
D. the number of virtual links in the areas
E. how well the areas can be summarized
F. the use of LSA filters

點擊查看答案

您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題When an OSPF design is planned, which implementation can help a router not have memory resource issues?（）

A. Have a backbone area (area 0) with 40 routers and use default routes to reach external destinations
B. Have a backbo ne area (area 0) with 4 routers and 30,000 external routes injected into OSPF
C. Have less OSPF areas to reduce the need for interarea route summarizations
D. Have multiple OSPF processes on each OSPF router. Example, router ospf 1, router ospf 2

點擊查看答案

2.單項選擇題 You have completed an OSPF implementation, and you are verifying OSPF operation. During this verification, you notice that the OSPF route of 172.16.10.0 is repeatedly appearing and disappearing from the routing table. Further investigation finds that the OSPF CPU utilization is very high and the routers are constantly performing SPF calculations. You determine that 172.16.20.2 is the source of the 172.16.10.0 route. Using the show ip ospf database router 172.16.20.1 command, you notice that when this show command is performed repeatedly, the contents of the LSA change every few seconds.
What could be the cause of this problem?（）

A. OSPF authentication errors between some of the routers
B. Two routers have the same OSPF router ID
C. Issues with mistuned OSPF timers
D. OSPF LSA pacing issues between some of the routers
E. OSPF neighbor adjacency problems between some of the routers

點擊查看答案

3.單項選擇題 Refer to the exhibit. You have completed an OSPF implementation, and you are verifying OSPF operation. You notice that router A and router B are stuck in the two - way state. From the show ip ospf interface command output, what is the cause of this issue?（）

A. All OSPF implementations must have at le ast one interface in area 0.
B. You are attempting to run in the broadcast mode over an NBMA interface.
C. Both routers are configured to function as a BDR; therefore, there is no DR router.
D. Someone has changed the OSPF router ID; therefore you must clear the OSPF process.
E. The OSPF priority is set to 0 on both routers; therefore neither can become the DR.

點擊查看答案

4.單項選擇題You have just completed an OSPF implementation. While executing your verification plan, you determine that R1 is not able to establish full OSPF adjacency with R2. The show ip ospf neighbor comman d output on R1 shows that R2 is stuck in the INIT state. What could be the cause of this problem?（）

A. DR and BDR election errors between R1 and R2.
B. The R2 router has not received the OSPF hello packets from the R1 router.
C. Mismatched interface ma ximum transmission unit (MTU) configuration between the R1 and R2.
D. Mismatched OSPF hello interval configuration between the R1 and R2
E. Corrupted LSAs exchanges between the R1 and R2.

點擊查看答案

5.單項選擇題 Refer to the exhibit. Looking at the topology diagram and the partial router configurations shown, which statement is true? （）

A.The NProuter has two OSPF neighbors in the "Full" adjacency state
B.The NProuter serial0/0 interface has the OSPF dead timer set to 10 seconds
C.The NProuter serial0/0 interface has been configured with an OSPF network type of "pointtopoint"
D.The 10.1.1.1 and 10.1.1.2 routers are not using the default OSPF dead and hello timers setting
E.The "Mismatched" error is caus ed by the expiration of the OSPF timers

點擊查看答案