A. an edge port that transitions to the forwarding state
B. a non-edge port that transitions to the blocking state
C. a non-edge port that transitions to the forwarding state
D. an edge port that transitions to the blocking state
E. any port that transitions to the blocking state
F. any port that transitions to the forwarding state
您可能感興趣的試卷
你可能感興趣的試題
A. active
B. speak
C. learn
D. listen
E. init
F. standby
You administer the network shown above. You issue the show interfaces trunk command on SwitchA and receive the following output：
SwitchA#show interfaces trunk
Port Mode Encapsulation Status Native vlan
Fa0/1 desirable -n802.1q trunking 1
Port Vlans allowed on trunk Fa0/1 1-4094
Port Vlans allowed and active in management domain
Fa0/1 1-9，31-37
Port Vlans in spanning tree forwarding state and not pruned
Fa0/1 1-9，31，33-37
Which of the following statements is true regarding VLAN 32？（）
A. VLAN 32 is not allowed on the trunk port.
B. VLAN 32 is not active on the switch.
C. Traffic from VLAN 32 is not being sent over the trunk port.
D. Traffic from VLAN 32 is not restricted to only the trunk ports that require it.
You want to configure a switched internetwork with multiple VLANs as shown above.
Which of the following commands should you issue on SwitchA for the port connected to SwitchB？ （）
A. switchport mode trunk
B. switchport access vlan 5
C. switchport mode access vlan 5
D. switchport trunk native vlan 5
Refer to the exhibit.
Which of the following should you do to configure the IP phone to override the priority of the data packets it receives from the host？ （）
A. Issue the mls qos trust cos command on the switch port connected to the IP phone.
B. Issue the switchport priority extend cos command on the switch port connected to the IP phone.
C. Issue the switchport priority extend cos command on the IP phone.
D. Issue the mls qos trust cos command on the IP phone.
You administer a network that uses two routers， R1 and R2， configured as an HSRP group to provide redundancy for the gateway. Router R1 is the active router and has been configured as follows：
R1#configure terminal
R1（config）#interface fa0/0
R1（config-if）#ip address 10.10.0.5 255.255.255.0
R1（config-if）#standby 1 priority 150
R1（config-if）#standby preempt delay minimum 50
R1（config-if）#standby 1 track interface fa0/2 15
R1（config-if）#standby 1 ip 10.10.0.20
Which of the following describes the effect the standby preempt delay minimum 50 command will have on router R1？（）
A. The HSRP priority for router R1 will increase to 200.
B. Router R1 will become the standby router if the priority drops below 50.
C. The HSRP priority for router R1 will decrease to 50 points when Fa0/2 goes down.
D. Router R1 will wait 50 seconds before attempting to preempt the active router.
最新試題
Which two statements about the various implementations of STP are true？（）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）
Which three statements are true of the Link Aggregation Control Protocol （LACP）？（）
Which three statements about STP timers are true？（）
DS2 has not become the active device for Vlan103’s HSRP group even though all interfaces are active. As related to Vlan103’s HSRP group. What can be done to make the group function properly ？ （）
Which two statements are true when the extended system ID feature is enabled？ （）
Refer to the exhibit. The command switchport mode access is issued on interface FastEthernet0/13 on switch CAT1. What will be the result？（）
What is the configured priority value of the Vlan105’s group on DS2 ？（）
Based on the show spanning-tree vlan 200 output shown in the exhibit， which two statements about the STP process for VLAN 200 are true？ （）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）