What can be determined about the HSRP relationship from the displayed debug output？ （）
A. Router 172.16.11.112 will be the active router because its HSRP priority is preferred over router 172.16.11.111.
B. Router 172.16.11.111 will be the active router because its HSRP priority is preferred over router 172.16.11.112.
C. The IP address 172.16.11.111 is the virtual HSRP router IP address.
D. The IP address 172.16.11.112 is the virtual HSRP router IP address.
E. The nonpreempt feature is enabled on the 172.16.11.112 router.
F. The preempt feature is not enabled on the 172.16.11.111 router.
您可能感興趣的試卷
你可能感興趣的試題
Examine the router output above.
Which two items are correct？ （）
A. The local IP address of Router A is 10.1.0.6.
B. The local IP address of Router A is 10.1.0.20.
C. If Ethernet 0/2 goesdown， the standby router will take over.
D. When Ethernet 0/3 of RouterA comes back up， the priority will become 105.
E. Router A will assume the active state if its priority is the highest.
Refer to the exhibit. Based upon the debug output that is shown，
which three statements about HSRP are true？（）
A. The router with IP address 172.16.11.111 haspreempt configured.
B. The final active router is the router with IP address 172.16.11.111.
C. The router with IP address 172.16.11.112 has nonpreempt configured.
D. The priority of the router with IP address 172.16.11.112 is preferred over the router with IP address 172.16.11.111.
E. The router with IP address 172.16.11.112 is using default HSRP priority.
F. The IP address 172.16.11.115 is the virtual HSRP IP address.
Refer to the exhibit.
Which two problems are the most likely cause of the exhibited output？（）
A. transport layer issues
B. VRRP misconfiguration
C. HSRP misconfiguration
D. physical layer issues
E. spanning tree issues
Examine the router output above. Which two items are correct？（）
A. The local IP address of Router A is 10.1.0.6.
B. The local IP address of Router A is 10.1.0.20.
C. If Ethernet 0/2 goesdown， the standby router will take over.
D. When Ethernet 0/3 of RouterA comes back up， the priority will become 105.
E. Router A will assume the active state if its priority is the highest.
What can be determined about the HSRP relationship from the displayed debug output？ （）
A. Router 172.16.11.112 will be the active router because its HSRP priority is preferred over router 172.16.11.111.
B. Router 172.16.11.111 will be the active router because its HSRP priority is preferred over router 172.16.11.112.
C. The IP address 172.16.11.111 is the virtual HSRP router IP address.
D. The IP address 172.16.11.112 is the virtual HSRP router IP address.
E. The nonpreempt feature is enabled on the 172.16.11.112 router.
F. The preempt feature is not enabled on the 172.16.11.111 router.
最新試題
What two things will occur when an edge port receives a BPDU？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Which statement is correct about the use of the virtual interface on a WLC ？（）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）
Refer to the exhibit. Which statement is true about the output？（）
Which option correctly identifies the Cisco IOS switching methods in descending order from the fastest method to the slowest method？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）