A. when all equipment is manufactured by Cisco
B. when there are multiple paths to destination networks
C. because having multiple routing protocols confuses hackers
D. when migrating from an older Interior Gateway Protocol (IGP) to a new IGP
E. when using UNIX host - based routers
F. when smaller broadcast domains are desired
您可能感興趣的試卷
你可能感興趣的試題
A. The multicast sources must register with the RP to form the multicast distribution tree.
B. An RP is required only in networks running Protocol Independent Multicast dense mode (PIM DM).
C. The mu lticast receivers must register with the RP to form the multicast distribution tree.
D. An RP is required only in networks running Protocol Independent Multicast sparse mode (PIM SM).
E. An RP is required only in networks running Protocol Independent Mu lticast sparse - dense mode (PIM - SDM).
F. To form the multicast distribution tree, the multicast sources register with and the receivers join the RP.
Refer to the exhibit. Based upon the information in the exhibit, which statement is true?()
A. DHCP requests from the host will be rebroadcasted to R2.
B. To complete t his configuration, the R1 fa0/0 interface must be configured with the ip helper - addresses command.
C. To complete this configuration, the R2 fa0/0 interface must be configured with the ip helper -addresses command.
D. R1 will forward all DHCP requests t o both 192.168.100.1 and 192.168.200.1 as unicast messages.
E. R1 will forward DHCP requests to 192.168.100.1. If there is no response, R1 will then forward the requests to 192.168.200.1.
Refer to the exhibit. Which configuration would correctly enable Host A to acquire an IP address from the DHCP server that is located at 10.1.2.10/24? ()
A.ASw1(config)# interface range FastEthernet 0/1 - 24 ASw1(config - if - range)# ip forward - protocol udp 67 ASw1(config - if - range)# ip forward - protocol udp 68
B.ASw1(config)# interface range FastEthernet 0/1 - 24 ASw1(config - if - range)# ip helper - address 10.1.2.10
C.RTA(config)# interface fastethernet0/0 RTA(config -if)# ip forward- protocol udp 67 RTA(config - if)# ip forwar d- protocol udp 68
D.RTA(config)# interface fastethernet0/1 RTA(config -if)# ip forward- protocol udp 67 RTA(config -if)# ip forward- protocol udp 68
E.RTA(config)# interface fastethernet0/0 RTA(config - if)# ip helper - address 10.1.2.10
F.RTA(config)# in terface fastethernet0/1 RTA(config - if)# ip helper - address 10.1.2.10
A. 2031:0:240F::09C0:123A:121B
B. 2031::240F::09C0:123A:121B
C. 2031::240F:9C0::123A:121B
D. 2031::240F:::09C0:123A:121B
Refer to the exhibit. Which statement is true about the router configuration that is shown ?Select the best response.()
A. Additional DHCP options will be imported from another DHCP server.
B. The DHCP server pools need to be bound to an interface to operate.
C. This configuration will provide IP configuration information to two different su bnets.
D. Additional DCHP option information needs to be imported from another DHCP server.
E. If the router hands out all the addresses in pool 1, then it will supply addresses from pool 2.
最新試題
An engineer is reviewing another engineer's sample configuration for a GRE tunnel used to pass IPv6 traffiC. The tunnel ha s not yet been configured on the router.Which of the following commands is not required for the configuration to pass IPv6 traffic?()
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?()
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?()
Which of the following is the shortest valid abbreviation for FE80:0000:0000:0000:0010:0000:0000:0123?()
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?()
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?()
Which of the following features work the same in both RIP- 2 and RIPng?()
Router R1 lists the following output from a show command. Which of the following is true about R1?()R1# show ip v6 interface f0/0FastEthernet0/0 is up, line protocol is upIPv6 is enabled, link - local address is FE80::213:19FF:FE12:3456No Virtual link - local address(es):Global unicast address(es):2000::4:213:19FF:FE12:3456, subnet is 2000:0:0:4::/64 [EUI]Jo ined group address(es):FF02::1FF02::2FF02::1:FF:12:3456
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?()
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?()ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0