Refer to the exhibit. What three statements are true about the IS - IS configuration?（）
A.The router is in area 49.0001.0002
B.The router acts as a Level 1 - 2 router
C.CLNS routing is enable d for the router
D.The router has a system ID of 0003.0004
E.The interfaces have a functional IS - IS configuration
F.The network service access point selector (NSEL) byte has a value of 0
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. This network is running IS - IS. Router RTC is inside Cloud#1. From the output on RTD, which two statement s are true?（）
A.Because it is running IS - IS in IP - only mode, RTD will not transmit CLNS packets
B.IP routing updates between RTC and RTD will be IP datagrams that are encapsulated by HDLC
C.The SNPA for RTE is the source data link address that is used to transmit frames to RTD
D.IP routing updates between RTC and RTD will be CLNS datagrams that are encapsulated by HDLC
E.The NET for RTE will be 49.0150.0019.06b7.fd5f.00
F.IP routing updates between RTC and RTD will be IP datagrams that a re encapsulated by CLNS
Refer to the exhibit. Router R1 is being used as a relay device for autoconfiguration of switch S1.Which configuration will acc omplish this? （）
A.S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 10.0.0.2
B.S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 20.0.0.1
C.R1(config)# interface fastethernet 0/0 R1(config - if)# ip help er - address 20.0.0.2R 1(config - if)# ip helper - address 20.0.0.3 R1(config - if)# ip helper - address 20.0.0.4 R1(config - if)# exit R1(config)# interface fastethernet 0/1 R1(config - if)# ip helper - address 10.0.0.1
D.R1(config)# interface fastethernet 0/0 R1 (config - if)# ip helper - address 20.0.0.1 R2(config)# interface fastethernet 0/0 R2(config - if)# ip helper - address 20.0.0.1 R3(config)# interface fastethernet 0/0 R3(config - if)# ip helper - address 20.0.0.1 R4(config)# interface fastethernet 0/0 R4(config - if)# ip helper - address 20.0.0.1
E.S1(config)# interface fastethernet 0/1 S1(config - if)# ip helper - address 10.0.0.2 R2(config)# interface fastethernet 0/0 R2(config - if)# ip helper - address 20.0.0.1 R3(config)# interface fastethernet 0/0 R3(config - if) # ip helper - address 20.0.0.1 R4(config)# interface fastethernet 0/0 R4(config - if)# ip helper - address 20.0.0.1
A. If a packet is sent to a multicast group address, the multicast frame contains the source multicast address.
B. A router does not have to be a member of a multicast group to recei ve multicast data.
C. A router must be a member of a multicast group to send to the group.
D. A router does not have to be a member of a multicast group to send to the group.
E. If a packet is sent to a multicast group address, all members of the multic ast group will receive it.
F. A router must be a member of a multicast group to receive multicast data.
A.Multicast addresses 224.0.0.13 and 224.0.0.22 are reserved link - local addresses used by PIMv2 and IGMPv3
B.Because they would map to overlapping IP multicast MAC addresses, multicast addresses 224.0.1.1 and 238.1.1.1 could not be used toget her
C.Multicast addresses 224.0.0.0 through 224.0.0.255 are always forwarded because they are transmitted with Time to Live (TTL) greater than 1
D.Multicast addresses 224.0.0.5 and 224.0.0.6 are source multicast addresses for OSPF routers
E.The a dministratively scoped multicast addresses 239.0.0.0 through 239.255.255.255 are similar in purpose to RFC 1918 private unicast addresses
F.Multicast address 224.0.1.1 has been reserved for the Network Time Protocol (NTP) by the IANA
A. The area cannot be a backbone area.
B. Inter area routes are suppressed.
C. The area has no more than 10 routers.
D. No virtual links are allowed.
E. No autonomous system border routers are allowed.
F. Redistribution is not allowed unless the packet is changed to a type 7 packet.
最新試題
The following configuration exists on a router on one end of an IPv6 tunnel. Although the configuration added so far is correct, the configuration is incomplete. Which type of tunnel is most likely to be intended by the network engineer？（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 2ipv6 address 2002:C0A8:10 1::1/64tunnel source loopback 1
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?（）
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, destined for an Enterprise network.Which of the following answers best describes the router's logic that tells the router, for a given packet, to apply GRE encapsulation to the packet?（）
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
Look at the following configuration below and select the statements that are true.（）RD2(config)#router ospf 100RD2(config - router)# distance 180 10.1.10.1 0.0.0.0 match - meRD2(config -router)#!RD2(config - router) #ip access - list standard match - meRD2(config - std - nacl)# permit host 172.16.0.0
Which of the following features work the same in both RIP- 2 and RIPng?（）
An enterprise has plans to start adding IPv6 support. The initial deployment requires support from some IPv6 - only device s that need to access servers that support only IPv4.Which of the following tools would be most appropriate?（）
Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE.Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?（）
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output？（）B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0