You have just purchased a new Cisco 3560 switch running the enhanced IOS and need configure it to be installed in a high availability network. On a 3560 EMI switch，
which three types of interfaces can be used to configure HSRP？（）
A. SVI interface
B. Access port
C. EtherChannel port channel
D. Loopback interface
E. Routed port
F. BVI interface
您可能感興趣的試卷
你可能感興趣的試題
A. QoS classified at layer 3 using IP precedence or DSCP.
B. Guaranteed rate service.
C. Implemented using FIFO queues.
D. All traffic has an equal chance of being dropped.
The Company is rolling out Cisco’s Architecture for Voice， Video and Integrated Data （AVVID）.
Which of the following choices represent the fundamental intelligent network services in Cisco’s AVVID？ （）
A. Quality of Service （QoS）
B. Intelligent platforms
C. Mobility and scalability
D. Security
E. High availability
Refer to the exhibit.
What is the effect when the switchport priority extend cos 3 command is configured on the switch port interface connected to the IP phone？（）
A. The IP phone is enabled to override with aCoS value of 3 the existing CoS marking of the PC attached to the IP phone.
B. The switch will no longer tag incoming voice packets and will extend the trust boundary to the distribution layer switch.
C. RTP will be used to negotiate aCoS value based upon bandwidth utilization on the link.
D. Effectively， the trust boundary has been moved to the PC attached to the IP phone.
E. The computer is now establishing theCoS value and has effectively become the trust boundary.
Refer to the exhibit.
Which Catalyst switch interface command would be used to cause the switch to instruct the phone to override the incoming CoS from the PC before forwarding the packet to the switch？（）
A. mls qos cos 2 override
B. switchport priority extend cos 11
C. switchport priority extend trust
D. switchport priority extend none
E. mls qos cos 2
F. switchport priority extend cos 2
You have configured voice VLANs on Catalyst switch R1.
Which two statements are true about the operation of voice VLANs on this device？ （）
A. When the voice VLAN feature is enabled， all untagged traffic is sent according to the default CoS priority of the port.
B. Enabling voice VLANs enables the switch to create multiple queues for traffic that is entering a port.
C. When voice VLANs are configured on a trunk link， UplinkFast must also be enabled.
D. Voice VLANs are configured to enable the switch to forward frames marked with the proper CoS values over separate physical links.
E. Enabling voice VLANs enables the switch to forward frames with a specific 802.1P marking.
最新試題
Refer to the exhibit. Based on the output of the show spanning-tree command， which statement is true？ （）
If G1/0/1 on DS1 is shutdown， what will be the current priority value of the Vlan105’s group on DS1 ？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
Refer to the exhibit. What will happen when one more user is connected to interface FastEthernet 5/1？ （）
Refer to the exhibit. Which statement is true about the output？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
During routine maintenance， G1/0/1 on DS1 was shutdown. All other interface were up. DS2 became the active HSRP device for Vlan101 as desired. However， after G1/0/1 on DS1 was reactivated. DS1 did not become the active HSRP device as desired. What need to be done to make the group for Vlan101 function properly ？ （）
Refer to the exhibit and the partial configuration of switch SW_A and SW_B. STP is configured on all switches in the network. SW_B receives this error message on the console port：00：06：34： %CDP-4-DUPLEX_MISMATCH： duplex mismatch discovered on FastEthernet0/5 （not half duplex）， with SW_A FastEthernet0/4 （half duplex） ， with TBA05071417（Cat6K-B） 0/4 （half duplex）. What would be the possible outcome of the problem？（）
What will occur when a nonedge switch port that is configured for Rapid Spanning Tree does not receive a BPDU from its neighbor for three consecutive hello time intervals？（）
During routine maintenance， it became necessary to shutdown G1/0/1 on DS1 and DS2. All other interface were up. During this time， DS1 became the active device for Vlan104’s HSRP group. As related to Vlan104’s HSRP group. What can be done to make the group function properly ？ （）