There is a connectivity problem between the serial 0/0 interface of router TESTKING1 and the serial 0/0 interface of TESTKING2. A leased line point to point circuit is installed between these two routers. The output from the "show interface serial 0/0" command is displayed below for each of these routers:
From your observations of the above exhibit, what is the underlying cause of the problem?（）
A. The loopback is not set.
B. The serial cable is faulty.
C. The subnet mask is not configured properly.
D. The IP address is not configured properly.
E. The Layer 2 frame types are not compatible.
F. The keepalive setting is not configured properly.
您可能感興趣的試卷
你可能感興趣的試題
The relevant configuration files for the TestKing1 and TestKing2 routers are displayed below:
With due consideration to the command outputs, which of the following reasons would you attribute the connectivity problem between the two routers?（）
A. The authentication needs to be changed to PAP for both routers.
B. The serial IP addresses of routers are not on the same subnet.
C. The username/password combination is incorrectly configured.
D. The router names are incorrectly configured.
A. ICMP echo request
B. Information interrupt request
C. Timestamp reply
D. Source quench
E. None of the above
The Testking router is running RIP as the routing protocol, and the IP routing table is displayed below:
Gateway of last resort is 10.1.2.2 to network 0.0.0.0
10.0.0.0/24 is subnetted, 2 subnets
R 10.1.3.0 [120/1] via 10.1.2.2, 00:00:00, Serial0/0
C 10.1.2.0 is directly connected, Serial0/0
C 10.1.5.0 is directly connected, Serial0/1
C 10.1.6.0 is directly connected, FastEthernet0/0
R* 0.0.0.0/0 [120/1] via 10.1.5.5, 00:00:00, Serial0/1
Based on the output above, if an administrator pings host 10.1.8.5 from host
10.1.6.100, how will the router TestkingA process the ICMP packets?（）
A. The packets will be discarded.
B. The packets will be routed out the S0/0 interface.
C. The packets will be routed out the S0/1 interface.
D. The packets will be routed out the Fa0/0 interface.
E. The packets will be routed through the 10.1.2.2 gateway.
A. duplex mismatch
B. a routing loop
C. trunking mode mismatch
D. improperly configured root bridge
E. improperly configured static VLAN
While troubleshooting connectivity issues, you log into a remote router. From there,you wish to see the layer 1 and layer 2 status of the interface.
Which of the following IOS commands would you issue to check the current IP addressing, as well as theyer 1 and layer 2 status of an interface?（）
A. TK1# show version
B. TK1# show protocols
C. TK1# show interfaces
D. TK1# show controllers
E. TK1# show ip interface
F. TK1# show startup-config
最新試題
Which of the following host addresses are member of networks that can be routed across the public Internet? （）
Given a subnet mask of 255.255.255.224, which of the following addresses can be assigned to network hosts?（）
Which statement describes the rule of split horizon?（）
What is the subnetwork address for a host with IP address 201.100.5.68/28?（）
New switches have been purchased for a network upgrade. The objective for the network design emphasizes efficient, error-free transport instead of fast transport.Which switching mode should be configured on the new switches to provide error-free transport to the network? （）
Five minutes after issuing the show running-config command, a technician enters the command again and notices that several access list statements have been altered. Because of this, the technician believes that the router is being configured by an unknown person through Telnet. Before changing the router passwords, the technician would like to discover if anyone is connected to the router by Telnet and stop them from making further changes.Which commands will accomplish these options?（）
What does a configuration Register Setting of 0x2105 indicate to the Router? （）
A Router with a BRI/T interface will be used for an ISDN Connection what other ISDN device is required to complete this connection? （）
Which of the following contribute to congestion on an Ethernet network?（）
Which of the following describe router functions?（）