Refer to the diagram. Which OSPF configuration command is required to configure Area 3 a s atotally stubby area?（）
A. On the ABR router ospf 10 area 3 stub
B. On all Area 3 routers router ospf 10 area 3 stub
C. On all Area 3 routers router ospf 10 area 3 stub no - summary
D. On the ABR router ospf 10 area 3 nssa
E. On the ABR rou ter ospf 10 area 3 stub no - summary
您可能感興趣的試卷
你可能感興趣的試題
The Dev - 1 and Dev -3 routers are OSPF neighbors over the Ethernet 0/0 connection. Based on the show ip ospf neighbor output from the Dev - 1 and Dev - 3 routers, which statement is true?（）
A. Dev - 1 is the DR because it has a lower OSPF router ID
B. Dev - 3 is the DR because it has a higher OSPF router priority
C. Both Dev - 1 and Dev - 3 are using the def ault OSPF router priority
D. Dev - 3 is the DR because it has a lower OSPF router ID
E. Dev - 1 is the DR because it has a higher OSPF router priority
During a recent OSPF election among three routers, RTA was elected the DR and RTB was elected the BDR, as seen in the graphic. Assume that RTA fails, and that RTB takes the place of
the DR whi le RTC becomes the new BDR. What will happen when RTA comes back online？（）
A. A new election will take place establishing an all new DR and BDR based on configured priority levels and MAC addresses.
B. RTA will take the place of DR immediately upon esta blishing its adjacencies.
C. RTA will take the place of DR only if RTB fails.
D. RTA will take the place of DR only if both RTB and RTC fail.
A. show ip protocol
B. show ip ospf
C. sho w ip ospf database
D. show ip ospf interface
Refer to the output. What IOS command produces this output？（）
A. show i p ospf
B. show ip ospf interface
C. show ipv6 ospf interface
D. show ipv6 ospf
Into which two types of areas would an area border router (ABR) inject a default route?（）
A. stub
B. the autonomous system of an exte rior gateway protocol (EGP)
C. NSSA
D. totally stubby
E. the autonomous system of a different interior gateway protocol (IGP)
F. area 0
最新試題
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?（）
Which of the following is helpful to allow an IPv6 host to learn the IP address of a default gateway on its subnet?（）
The following output on Router R1 lists details of a BGP route for 190.1.0.0/16. Which of the following is true based on this output?（）R1# show ip bgp 19 0.1.0.0/16BGP routing table entry for 190.1.0.0/16, version 121Paths: (1 available, best #1, table Default - IP - Routing - Table)Advertised to update - groups:11 2 3 41.1.1.1 from 2.2.2.2 (3.3.3.3)Origin IGP, metric 0, localpref 100, valid, internal, best
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?（）
Router R1 connects to Router R2 over an Ethernet LAN with both routers using their F0/0 interfaces. R1 learns a route from R2 using EIGRP f or IPv6. That route lists F0/0 as the outgoing interface with R2 as the next hop. The configuration excerpt shows all relevant configuration on R2's F0/0 interface. Which of the following is true about R1's route?（）interface f0/0mac - address 1111.1111.1 111ipv6 address 2000::/64 eui - 64ipv6 address 2001::1/64
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?（）ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
Router R1 use s MAC address 1111.1111.1111 for its Fa0/0 interface. An engineer sees the following configuration in the output of a show running - config command. Then, the engineer issues a show ipv6 interface brief command. What global unicast IPv6 address does this c ommand display for interface tunnel 1?（）interface loopback 1ip address 192.168.1.1 255.255.255.255interface tunnel 1tunnel source loopback 1tunnel destination 192.168.1.2tunnel mode ipv6ip isatapipv6 address 2000::/64 eui - 64
An Enterprise rou ter, Ent1, displays the following excerpt from the show ip bgp command. ENT1 has an eBGP connection to an ISP router with address 3.3.3.3 and an iBGP connection to a router with address 4.4.4.4. Which of the following is most likely to be true?（）Network Next Hop Metric LocPrf Weight Path*> 3.3.3.3 0 0 1 1 1 1 218 i
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1