A. The IP addresses of workstations allowed gain access to the router via an access list
B. Permanent name-to-address mappings created using the ip host command.
C. Temporary and permanent DNS entries.
D. The names of the routers created using the hostname command.
E. The length of time of users logged into the router, as well as the duration
您可能感興趣的試卷
你可能感興趣的試題
A. application layer
B. session layer
C. transport layer
D. internet layer
E. network layer
F. data link layer
G. physical layer
A. The Popcorn router is not forwarding RIP updates.
B. The Popcorn router did not include network 192.168.12.0 in its routing configuration.
C. The Ethernet1 interface of the Popcorn router is shutdown.
D. The clockrate is not present in the configuration of one of the routers.
E. The Serial interface of the Popcorn router is not operating.
A. TK1#show ip eigrp adjacency
B. TK1#show ip eigrp topology
C. TK1#show ip eigrp interfaces
D. TK1#show ip eigrp neighbors
E. None of the above
A new router, named TK1, is being installed. You wish to add this router to your existing OSPF network. In doing so, you configure the following:
TK1(config)# router ospf 1
TK1(config-router)# network 10.10.10.0 255.255.255.0 area 0
After making this change, you notice that the networks attached to TK1 are not being learned by the other OSPF routers. What could be the cause of this?（）
A. The AS is not correctly configured
B. The network subnet mask is incorrectly configured
C. The network wildcard mask is configured incorrectly
D. The network number is not correctly configured
E. The process id is configured incorrectly
F. None of the above
On your OSPF network, routers TK1 and TK2 belong to the same Ethernet network. However, they are unable to establish an adjacency over this link. While troubleshooting this problem, you issue the "show ip ospf interface Ethernet 0"command on each router. The output from these commands is displayed below:
What is the underlying cause of the routers failing to become adjacent?（）
A. The OSPF area is misconfigured.
B. The priority on TK2 should be set lower.
C. The cost on TK2 should be set lower.
D. The hello and dead timers are misconfigured.
E. You need to add a backup designated router to the network.
F. The OSPF process ID numbers do not match.
最新試題
Five minutes after issuing the show running-config command, a technician enters the command again and notices that several access list statements have been altered. Because of this, the technician believes that the router is being configured by an unknown person through Telnet. Before changing the router passwords, the technician would like to discover if anyone is connected to the router by Telnet and stop them from making further changes.Which commands will accomplish these options?（）
The network 172.12.0.0 needs to be divided into subnets where each subnet has the capacity of 458 IP addresses.What would be the correct subnet mask to accomplish this division keeping the number of subnets at the maximum? （）
The following access list was applied outbound on he E0 interface connected to the 192.168.1.8/29 LAN:access-list 123 deny tcp 192.168.1.8 0.0.0.7 eq 20 anyaccess-list 123 deny tcp 192.168.1.9 0.0.0.7 eq 21 anyWhat effect will this access list have?（）
What is the subnetwork address for a host with IP address 201.100.5.68/28?（）
Which of the following describe router functions?（）
Which command is required for connectivity in a Frame Relay network if Inverse ARP is not operational? （）
What feature of a networks switch allows an administrative to create separate broadcast domains?（）
Which of the following options lists the steps in PPP session establishment in the correct order?（）
A network host is configured as follows: Host IP address: 192.168.16.183 Subnet mask: 255.255.255.224 Default gateway: 192.168.16.190 Which of the following statements describe the network to which this host is attached?（）
You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?（）