A. The i nterface used by one router to connect to the other router is passive in the EIGRP process.
B. Duplicate EIGRP router IDs.
C. Mismatched Hold Timers.
D. IP addresses of 10.1.1.1/24 and 10.2.2.2/24, respectively.
您可能感興趣的試卷
你可能感興趣的試題
Router R1 has been configured with the commands rout er eigrp 9 and network 172.16.2.0 0.0.0.255, with no other current EIGRP configuration. R1's (working) Fa0/0 interface has been configured with IP address 172.16.2.2/26. R1 has found three EIGRP neighbors reachable via interface Fa0/0, including the rou ter with IP address 172.16.2.20. When the engineer attempts to add the neighbor 172.16.2.20 fa0/0 command in EIGRP configuration mode.
Which of the following occurs？（）
A.Fa0/0 fails
B.The command is rejecteD
C.The existing three neighbors fail
D.The neighborship with 172.16.2.20 fails and then reestablishes
E.None of the other answers is correct
Routers R1 and R2, currently EIGRP neighbors over their Fa0/0 interfaces (respectively),both use EIGRP authentication. Tuesday at 8 p.m. the neighborship fails.
Which of the following wo uld not be useful when investigating whether authenticationhad anything to do with the failure？（）
A. debug eigrp packet
B. show key chain
C. show ip eigrp neighbor failure
D. show clock
Routers R1 and R2 are EIGRP neighbors using their Fa0/0 interfaces, respectively. An engineer adds the ip hello - interval eigrp 9 6 command to R1's Fa0/0 configuration.
Which of the following is true regarding the results from this c hange？（）
A.The show ip eigrp neighbors command on R1 lists the revised Hello timer
B.The show ip eigrp interfaces command on R1 lists the revised Hello timer
C.The R1 - R2 neighborship fails due to Hello timer mismatcH
D.The show ip eigrp interfaces detail command on R1 lists the revised Hello timer
Router R1 has working interfaces S0/0, S0/1, and S0/2, with IP address/prefix combinations of 10.10.10.1/24, 10.10.11.2/24, and 10.10.12.3/22. R1's configuration includes the command s router eigrp 9 and network 10.0.0.0. The show ip eigrp interfaces command lists S0/0 and S0/1 in the command output, but not S0/2.
Which answer gives the reason for the omission？（）
A. R1 has EIGRP neighbors reachable via S0/0 and S0/1, but not via S0/2, so it is not included.
B. S0/2 may currently be in a state other than up/up.
C. The network 10.0.0.0 command requires the use of mask 255.0.0.0 due to EIGRP being classful by default.
D. S0/2 may be configured as a passive inter face.
A router has been configured with the commands router eigrp 9 and network 72.16.1.0 0.0.0.255. No other EIGRP - related commands have been configured. The nswers list the IP addresses that could be assigned to this router's Fa0/0 interface.
Which answers list an IP address/prefix length that would cause the router to enable IGRP on Fa0/0?（）
A. 172.16.0.1/23
B. 172.16.1.1/26
C. 172.16.1.1/24
D. 172 .16.0.255/23
E. None of the other answers is correct.
最新試題
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?（）
Which of the following answers lists a multicast IPv6 address?（）
An enterprise h as plans to start adding IPv6 support. For the first year, the IPv6 will be in small pockets spread around the existing large IPv4 network, with occasional IPv6 traffic while applications teams test IPv6 - enabled servers and applications.Which of the fol lowing tools would be most appropriate?（）
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exis ts in a planning document intended to be used to copy/paste into Router R1 to enable EIGRP for IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about EIGRP for IPv6 on R1 after this configuration has been pasted into R1?（）ipv6 router eigrp 1ipv6 unicast- routinginterface f0/0ipv6 address 2000::1/64ipv6 eigrp 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 eigrp 1
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?（）
Which of the following are true of both OSPFv2 and OSPFv3?（）
Router R1 sits at an Enterprise branch office, using the Internet for its only connectivity back to the rest of the EnterprisE.Which of the following is not a ben efit of using an IPsec tunnel for packets sent through the Internet, between R1 and the rest of the Enterprise?（）
Router R1 sits at an Enterprise branch office, using both the Internet and a leased line to another Enterprise router for its two connectivity options back into the rest of the Enterprise network. The engineer planning for this branch decided to use the leased line for all Enterprise traffic, unless it fails, in which case the Internet connection should be used to pass traffic to the Enterprise.Which of the following is most likely to be useful on the branch router?（）
Router R1 has two LAN interfaces and three serial interfaces enabled for IPv6. All the inte rfaces use link local addresses automatically generated by the router.Which of the following could be the link local address of R1's interface S0/0?（）
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?（）