Refer to the exhibit. Router RTA is the hub router for routers RTB and RTC. The Frame Relay network is configured with EIGRP, and the entire network is in autonomous system 1. However,router RTB a nd RTC are not receiving each other's routes. What is the solution?()
A.Check and change the access lists on router RTA
B.Configure the auto summary command under router eigrp 1 on router RTA
C.Configure subinterfaces on the spoke routers and assig n different IP address subnets for each subinterface
D.Issue the no ip split horizon command on router RTA
E.Issue the no ip split horizon eigrp 1 command on router RTA
F.Configure a distribute list on router RTA that allows it to advertise all r outes to the spoke routers
您可能感興趣的試卷
你可能感興趣的試題
Refer to the exhibit. EIGRP has been configured on all routers in the network. What additional configur ation statement should be included on router R4 to advertise a default route to its neighbors?()
A. R4(config)# ip route 0.0.0.0 0.0.0.0 10.1.1.1
B. R4(config)# ip default - network 10.0.0.0
C. R4(config - router)# default -information originate
D. R4(conf ig)# ip route 10.0.0.0 255.0.0.0 10.1.1.1
最新試題
Which of the following answers lists either a protocol or function that can be used by a host to dynamically learn its own IPv6 address?()
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable OSPFv3 on interfaces F0/0 and S0/0/0. No other related configuration exists. Assuming F0/0 and S0/0/0 reach an up/up state, which of the following is true about OSPFv3 on R1 after this configuration has been pasted into R1?()ipv6 router ospf 1ipv6 unicast- routinginterface f0/0ipv6 address 2000 ::1/64ipv6 ospf 1 area 1interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 ospf 1 area 0
The answers each list a tunnel method and two consecutive IPv6 address quartets.Which answers identify a tunneling method that relies on an IPv4 address to be embedded into an IPv6 address, within the correct quartets listed?()
Router R1 has been conf igured with an ipv6 route 2000::/64 S0/0/0 64 command.Which of the following does the 64 at the end of the command represent?()
Which of the following IPv6 tunneling mechanisms support IPv6 IGP routing protocols?()
Router R1 has the following configuration. Assuming R1's F0/0 interface has a MAC address of 0200.0011.1111, what IPv6 addresses will R1 list for interface F0/0 in the output of the show ipv6 interface brief command?()interface f0/0ipv6 address 2345:0:0:8::1/64
The following line of output was gathered on Enterprise Router Ent1 using the command show ip route. Which of the following answers is most likely to be true, based on thi s output?()B 128.107.0.0 [20/10] via 11.11.11.11, 00:02:18
Router R1 currently has no configuration related to IPv6 or IPv4. The following configuration exists in a planning document, intended to be used to copy/paste into Router R1 to enable RIPng and IPv6 on interfaces F0/0 and S0/0/0. No other related configuration exists. Which of the following is true about RIPng on R1 after this configuration has been pasted into R1?()ipv6 unicast- routinginterface f0/0ipv6 rip one enableipv6 address 2000::1/64interface s0/0/0ipv6 address 2001::/64 eui - 64ipv6 rip one enable
Router R1, a branch router, connects to the Internet using DSL. Some traffic flows through a GRE and IPsec tunnel, over the DSL connection, and into the core of an Enterprise network. The branch also allows local hosts to communicate directly with public sites in th e Internet over this same DSL connection.Which of the following answers defines how the branch NAT config avoids performing NAT for the Enterprise directed traffic but does perform NAT for the Internet - directed traffic?()
Router R1, a branch router, connects to the Internet using DSL. The engineer plans to use a configuration with a dialer interface. The answers list a feature and interface on which the feature could be configured.Which combinations accurately describe the interface under which a feature will be configured?()