You’re a network administer and you issue the command （show port 3/1） on an Ethernet port. To your surprise you notice a non-zero entry in the ’Giants’ column.
What could be the cause of this？ （）
A. IEEE 802.1Q
B. IEEE 802.10
C. Misconfigured NIC
D. User configuration
E. All of the above
您可能感興趣的試卷
你可能感興趣的試題
The Company administrator has issue the "show vlan id 5" command.
What will this command display？ （）
A. Ports in VLAN 5
B. Utilization
C. VLAN information on port 0/5
D. Filters
E. MTU and type
Which of the following should you enable to prevent a switch from forwarding packets with source addresses that are outside an administratively defined group？ （）
A. DAI
B. STP
C. PVLAN
D. port security
Refer to the exhibit. The switchport output in Figure 1 displays the default settings of interface FastEthernet 0/13 on switch SW1. Figure 2 displays the desired interface settings.
Which command sequence would configure interface FastEthernet 0/13 as displayed in Figure 2？ （）
A. SW1（config-if）# switchport trunk encapsulation dot1q SW1（config-if）# switchport mode trunk SW1（config-if）# switchport trunk native DATA SW1（config-if）# switchport trunk allowed vlan 1，10，20
B. SW1（config-if）# switchport trunk encapsulation dot1q SW1（config-if）# switchport mode dynamic auto SW1（config-if）# switchport trunk native DATA SW1（config-if）# witchport trunk allowed vlan add 1，10，20
C. SW1（config-if）# switchport trunk encapsulation dot1q SW1（config-if）# switchport mode dynamic desirable SW1（config-if）# switchport trunk native vlan DATA SW1（config-if）# switchport trunk allowed vlan 1，10，20
D. SW1（config-if）# switchport trunk encapsulation dot1q SW1（config-if）# switchport mode dynamic desirable SW1（config-if）# switchport trunk native vlan 10 SW1（config-if）# switchport trunk allowed vlan 1，10，20
E. SW1（config-if）# switchport trunk encapsulation dot1q SW1（config-if）# switchport mode dynamic Desirable SW1（config-if）# switchport trunk native vlan 10
You need make configuration changes to an existing layer 3 switch in the Company network. On a multilayer Catalyst switch，
which interface command is used to convert a Layer 3 interface to a Layer 2 interface？（）
A. switchport access vlan vlan-id
B. switchport
C. switchport mode access
D. no switchport
E. None of the other alternatives apply
Refer to the exhibit. The user who is connected to interface FastEthernet 0/1 is on VLAN 10 and cannot access network resources. On the basis of the information in the exhibit，
which command sequence would correct the problem？（）
A. SW1（config）# vlan 10SW1（config-vlan）# no shut
B. SW1（config）# interface fastethernet 0/1SW1（config-if）# switchport mode accessSW1（config-if）# switchport access vlan 10
C. SW1（config）# interface fastethernet 0/1SW1（config-if）# switchport mode access
D. SW1（config）# vlan 10SW1（config-vlan）# state active
E. SW1（config）# interface fastethernet 0/1SW1（config-if）# no shut
最新試題
Refer to the exhibit. Which Virtual Router Redundancy Protocol （VRRP） statement is true about the roles of the master virtual router and the backup virtual router？（）
Which router redundancy protocol cannot be configured for interface tracking？（）
Refer to the exhibit. What command was issued on the Layer 3 switch Sw1 between Exhibit #1 and Exhibit #2？（）
Which two statements about the various implementations of STP are true？（）
Refer to the exhibit. What does the command channel-group 1 mode desirable do？ （）
Which statement is correct about the use of the virtual interface on a WLC ？（）
Refer to the exhibit. Initially， LinkA is connected and forwarding traffic. A new LinkB is then attached between SwitchA and HubA. Which two statements are true about the possible result of attaching the second link？（）
Refer to the exhibit. LACP has been configured on Switch1 as shown. Which is the correct command set to configure LACP on Switch2？（）
How are STP timers and state transitions affected when a topology change occurs in an STP environment？（）
What must be the same to make multiple switches part of the same Multiple Spanning Tree （MST）？（）