多項選擇題What kind of information can you deduce from an IOS image file name?()

A. Distribution channel failures
B. Feature capabilities
C. Memory capacity needs
D. Hardware product platform
E. Programming language requirements
F. Run location and compression status


您可能感興趣的試卷

你可能感興趣的試題

1.單項選擇題After issuing the "show version" command on your Cisco router, you notice that the image is named "C7200-ajs40-mx". What does the C7200 portion of the filename represent?()

A. The memory capacity requirements
B. The hardware product platform
C. The distribution channel
D. The feature capabilities
E. The run location and compression status

2.單項選擇題You need to upgrade the IOS of an existing router on your network. The new IOS image is located on a TFTP server that you have set up within the network. What command should you issue in order to download the new IOS version?()

A. Router# copy tftp flash
B. Router# copy flash run
C. Router(config)# restore flash
D. Router(config)# repair flash
E. Router#copy flash tftp
F. Router# copy start flash

3.單項選擇題

After making changes to the router, you issue the "copy running-config startup-config" command to save changes. After reloading the router, the router comes up in setup mode. You again make changes, save them, and reboot. Again,the router comes up in setup mode.
What is the most likely cause of this?()

A. The NVRAM is corrupted.
B. The boot system commands were omitted in the configuration.
C. The configuration register setting is incorrect.
D. The upgraded configuration incompatible with the hardware platform.
E. The upgraded IOS incompatible with the hardware.

4.多項選擇題Which of the following commands will display the name of the IOS image file being used in a Cisco router?()

A. Router# show IOS
B. Router# show version
C. Router# show image
D. Router# show protocols
E. Router# show flash

5.單項選擇題You are a senior network administrator at TestKing, and while performing thepassword recovery procedure on your 2500 series Cisco router, you type in thefollowing command:o/r 0x2142What is the purpose of this command?()

A. It is used to restart the router.
B. It is used to bypass the configuration in NVRAM.
C. It is used to enter ROM Monitor mode.
D. It is used to view the lost password.
E. It is used to save the changes to the configuration.

最新試題

Which of the following correctly describe steps in the OSI data encapsulation process?()

題型:多項選擇題

What is the subnetwork address for a host with IP address 201.100.5.68/28?()

題型:單項選擇題

Which of the following statements regarding routed and routing protocols are true?()

題型:多項選擇題

A network host is configured as follows: Host IP address: 192.168.16.183 Subnet mask: 255.255.255.224 Default gateway: 192.168.16.190 Which of the following statements describe the network to which this host is attached?()

題型:多項選擇題

The network 172.12.0.0 needs to be divided into subnets where each subnet has the capacity of 458 IP addresses.What would be the correct subnet mask to accomplish this division keeping the number of subnets at the maximum? ()

題型:單項選擇題

An administrator would like to configure a switch over a virtual terminal connection from locations outside of the local LAN. Which of the following are required in order for the switch to be configured from a remote location? ()

題型:多項選擇題

All WAN links is side the TestKing.com network use PPP with for authentication security. Which command will display the CHAP authentication process as it occurs between two routers in the network?()

題型:單項選擇題

Which command is used to display the placement and direction of an IP access control list on a router?()

題型:單項選擇題

You are configuring a new Catalyst switch that you want to manage remotely from workstations on other network segments within your enterprise.Which of the following are required to allow remote management of the switch over IP?()

題型:多項選擇題

Which of the following contribute to congestion on an Ethernet network?()

題型:多項選擇題