A.Router ACLs can be applied to the input and output directions of a VLAN interface
B.Bridged ACLs can be applied to the input and output directions of a VLAN interface
C.Only router ACLs can be applied to a VLAN interface
D.VLAN maps and router ACLs can be used in combination
E.VLAN maps can be applied to a VLAN interfac
您可能感興趣的試卷
你可能感興趣的試題
A.Trunk
B.Isolated
C.Primary
D.Community
E.Promiscuous
F.None of the other alternatives apply
Refer to the exhibit. The user who is connected to interface FastEthernet 0/1 is on VLAN 10 andcannot access network resources. On the basis of the information in the exhibit， which commandsequence would correct the problem？（）
A.SW1（config）# interface fastethernet 0/1 SW1（config-if）# no shut
B.SW1（config）# interface fastethernet 0/1 SW1（config-if）# switchport mode access SW1（config-if）# switchport access vlan 10
C.SW1（config）# vlan 10 SW1（config-vlan）# state active
D.SW1（config）# interface fastethernet 0/1 SW1（config-if）# switchport mode access
E.SW1（config）# vlan 10 SW1（config-vlan）# no shut
You work as a network Technician. A new workstation has consistently been unable to obtain anIP address from the DHCP server when the workstation boots. Older workstations function
normally， and the new workstation obtains an address when manually forced to renew its address.
What should be configured on the switch to allow the workstation to obtain an IP address at boot？（）
A.UplinkFast on the switch port connected to the server
B.BackboneFast on the switch port connected to the server
C.PortFast on the switch port connected to the workstation
D.trunking on the switch
A.Ports in VLAN 5
B.Utilization
C.VLAN information on port 0/5
D.Filters
E.MTU and type
Refer to the exhibit. On the basis of the output generated by the show commands， which twostatements are true？（）
A.All interfaces on the switch have been configured as access ports
B.Because it has not been assigned to any VLAN， interface gigabitethernet 0/1 does not appearin the show vlan output
C.Because it is configured as a trunk interface， interface gigabitethernet 0/1 does not appear inthe show vlan output
D.There are no native VLANs configured on the trunk
E.VLAN 1 will not be encapsulated with an 802.1q header
F.VLAN 2 will not be encapsulated with an 802.1q header
最新試題
Drag and drop the steps in the process for provisioning a cable modem to connect to a headendon the above to the below in the order defined by the DOCSIS standard.
cisco ios command to interface dialer 0
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clicking the numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible.To gain access to either the topology or the SDK click on the button to left side of the screen thatcorresponds to the section you wish to access. When you have finished viewing the topology theSDK you can return to your questions by clicking on the Questions button to the left.Which defined peer IP address an local subnet belong to Crete？（）
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）
Match the xDSL type on the above to the most appropriate implementation on the below.
Which statement correctly describes IPsec VPN backup technology？（）
Drag the correct statements about MPLS-based VPN on the left to the boxes on the right.（Not allstatements will be used）
Study this exhibit carefully. What information can be derived from the SDM firewall configurationdisplayed？（）
Router NetworkTut is configured as shown below：Given the above configuration， which statement is true？（）
Which two encapsulation methods require that an 827 ADSL router be configured with a PPPusername and CHAP password？（）