A.debug eigrp packets
B.show ip eigrp traffic
C.show ip eigrp topology
D.show ip eigrp neighbors
您可能感興趣的試卷
你可能感興趣的試題
A.Some query or reply packets are lost between the routers
B.The neighboring router starts receiving route updates from this router
C.A failure causes traffic on a link between two neighboring routers to flow in only one direction（unidirectional link）
D.The neighboring router stops receiving ACK packets from this router
Refer to the exhibit. EIGRP has been configured on routers R1 and R2. However， R1 does notshow R2 as a neighbor and does not accept routing updates from R2. What could be the cause ofthe problem？（）
A.The no auto-summary command has not been issued under the EIGRP process on bothrouters
B.Interface E0 on router R1 has not been configured with a secondary IP address of 10.1.2.1/24
C.EIGRP cannot exchange routing updates with a neighbor’s router interface that is configuredwith two IP addresses
D.EIGRP cannot form neighbor relationship and exchange routing updates with a secondaryaddress
Based on the above configuration, which of the following BGP statements would inject the 10.10.0.0/16 prefix into the BGP routing table（）
A.network 10.0.0.0
B.network 10.10.0.0 mask 255.255.0.0
C.network 10.10.10.1 mask 255.255.255.255
D.network 10.10.10.0 mask 255.255.255.0
E.network 10.0.0.0 mask 255.255.0.0
Study the exhibit below carefully：
If the configuration shown below is added to Router1， which three route entries will EIGRPadvertise to neighboring routers？（）
router eigrp 10
network 10.0.0.0
eigrp stub
A.192.168.20.0/24
B.10.1.2.0/24
C.10.1.1.0/24
D.10.1.3.0/24
E.10.0.0.0/8
A.The IBGP routers must always be fully meshed.
B.The IBGP routers can be in a different AS.
C.The IBGP routers must be directly connected.
D.TThe IBGP routers do not need to be directly connected.
E.None of the other alternatives apply are true
最新試題
Drag the IOS commands from the left that would be used to implement a GRE tunnel using the10.1.1.0.30 network on interface serial 0/0 to the correct target area on the right.
cisco ios command to interface dialer 0
Drag the DSL technologies on the left to their maximum（down/up） data rate values on the below.
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
Network Topology Exhibit：Configuration Exhibit：NET（config）# access-list 112 deny icmp any any echo logNET（config）# access-list 112 deny imp any any redirect logNET（config）# access-list 112 deny icmp any any mask-request logNET（config）# access-list 112 permit icmp any 10.1.1.0 0.0.0.255NET（config）# interface Fa0/1NET（config-if）# ip access-group 112 inYou work as a network administrator at networkTut.com， study the exhibit carefully. Theconfiguration has been applied to router NET to mitigate the threat of certain types of ICMPbasedattacks while allowing some ICMP traffic to the corporate LAN to work. However， the configurationis incorrect. On the basis of the information in the exhibit， which configuration option wouldcorrectly configure router NET？（）
Drag the protocols that are used to distribute MPLS labels from the above to the target area on thebelow.（Not all options will be used）
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define？（）
Which statement about PPPoA configuration is correct？（）
Drag and drop question. The upper gives the MPLS functions， the bottom describes the planes.Drag the above items to the proper location at the below
Drag and drop the xDSL type on the above to the appropriate xDSL description on the below.