A.The neighboring router stops receiving ACK packets from this router.
B.The neighboring router starts receiving route updates from this router.
C.The neighboring router is too busy to answer the query(generally caused by high CPU utilization).
D.The neighboring router is having memory problems and cannot allocate the memory to process the query or build the reply packet.
您可能感興趣的試卷
你可能感興趣的試題
A.Lay er 5
B.Lay er 4
C.Lay er 3
D.Lay er 2
E.Lay er 1
A.The Aironet Desktop Utility (ADU )profile manager feature can create and manage only one profile for the wireless client adapter.
B.The Aironet Desktop Utility (ADU) can support only one wireless client adapter installed and used at a time.
C.The Aironet Desktop Utility (ADU) can be used to establish the association between the client adapter and the access point , manage authentication to the wireless network , and enable encryption.
D.The Aironet Desktop Utility (ADU) and the Microsoft Wireless Configuration Manager can be used at the same time to configure the wireless client adapter.
The network setup for this trouble ticket is shown in Figure 3.
Trouble Ticket Statement
DSW1 and R4 cannot ping R2’s loopback or R2’s s0/0/0/0.12 IPv6 address. Initial troubleshooting showsand R2 is not an OSPFv3 neighbor on R3.
Configurationon R2
ipv6 unicast-routing!
ipv6 router ospf 6
router-id 2.2.2.2!
interface s0/0/0/0.23
ipv6 address 2026::1:1/122
ConfigurationR3
ipv6 unicast-routing!
ipv6 router ospf 6
router-id 3.3.3.3!
interface s0/0/0/0.23
ipv6 address 2026::1:2/122
ipv6 ospf 6 area 0
Figure 3
What is the solution of the fault condition?()
A.Add ipv6 ospf 6 area 0 under S0/0/0/0.23 on R2
B.Add ipv6 ospf 6 area 6 under s0/0/0/0.23 on R2
C.Remove IPv6 address from s0/0/0/0.23 on R2
D.Enable IPv6 routing on s0/0/0/0.23 on R2
The network setup for this trouble ticket is shown in Figure 3.
Trouble Ticket Statement
DSW1 and R4 cannot ping R2’s loopback or R2’s s0/0/0/0.12 IPv6 address. Initial troubleshooting shows and R2 is not an OSPFv3 neighbor on R3.
Configurationon R2
ipv6 unicast-routing!
ipv6 router ospf 6
router-id 2.2.2.2!
interface s0/0/0/0.23
ipv6 address 2026::1:1/122
ConfigurationR3
ipv6 unicast-routing!
ipv6 router ospf 6
router-id 3.3.3.3!
interface s0/0/0/0.23
ipv6 address 2026::1:2/122
ipv6 ospf 6 area 0
Figure 3
The Fault Condition is related to which technology?()
A.IPv6 Addressing
B.Route Redistribution
C.OSPFv3
D.RIPng
最新試題
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec, which two parameters are required when defining the tunnel interfaceinformation?()
Drag the correct statements about MPLS-based VPN on the left to the boxes on the right.(Not allstatements will be used)
Which two encapsulation methods require that an 827 ADSL router be configured with a PPPusername and CHAP password?()
Drag and drop the xDSL type on the above to the appropriate xDSL description on the below.
As a network engineer, do you know for what purpose SDM uses Security Device Event Exchange(SDEE)?()
Drag each element of the Cisco IOS Firewall Feature Set from the above and drop onto itsdescription on the below.
Drag and drop question. The upper gives the MPLS functions, the bottom describes the planes.Drag the above items to the proper location at the below
A new router was configured with the following commands:The configuration above was found on an Internet Service Provider’s (ISP) Multiprotocol LabelSwitching (MPLS) network. What is its purpose?()
Drag the IOS commands from the left that would be used to implement a GRE tunnel using the10.1.1.0.30 network on interface serial 0/0 to the correct target area on the right.
cisco ios command to interface dialer 0