Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Figure 2
Trouble Ticket Statement
Client 1 and Client 2 are getting a 169.x.x.x IP address and are not able to ping DSW1 or the FTP Server.They are able to ping each other.
Configurationon ASW1
Interface FastEthernet1/0/1
switchport mode access
switchport access vlan 1!
Interface FastEthernet1/0/2
switchport mode access
switchport access vlan 1
The Fault Condition is related to which technology？（）
A.VLAN
B.InterVLAN communication
C.DHCP
D.Port Security
您可能感興趣的試卷
你可能感興趣的試題
Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Figure 2
Trouble Ticket Statement
Client one is getting a 169.x.x.x IP address and is not able to ping Client 2 or DSW1. Inital troubleshootingshows that port Fa1/0/1 on ASW1 is in errdisable state.
Configurationon ASW1
Interface FastEthernet1/0/1
switchport mode access
switchport port-security
switchport port-security mac-address 0000.0000.0001
What is the solution of the fault condition？（）
A.Configurationure Static IP Address on Client 1
B.Change the IP Address of VLAN 10 on DSW1
C.Issue shutdown command followed by no shutdown command on port fa1/0/1 on ASW1
D.Issue no switchport port-security mac-address 0000.0000.0001 command followed by shutdown and noshutdown command on port fa1/0/1 on ASW1
E.Issue no switchport port-security mac-address 0000.0000.0001 command on port fa1/0/1 on ASW1
Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Figure 2
Trouble Ticket Statement
Client one is getting a 169.x.x.x IP address and is not able to ping Client 2 or DSW1. Inital troubleshootingshows that port Fa1/0/1 on ASW1 is in errdisable state.
Configurationon ASW1
Interface FastEthernet1/0/1
switchport mode access
switchport port-security
switchport port-security mac-address 0000.0000.0001
The Fault Condition is related to which technology？（）
A.VLAN Access Map
B.InterVLAN communication
C.DHCP
D.Port Security
Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Figure 2
Trouble Ticket Statement
Client 1 is getting an IP address from the DHCP server but is not able to ping DSW1 or the FTP
Cisco 642-832： Practice ExamServer
Configurationon DSW1
vlan access-map test1 10drop
match ip address 10!
vlan filter test1 vlan-list 10!
ip access-list standard 10permit 10.2.0.0 0.0.255.255!
Interface VLAN10
ip address 10.2.1.1 255.255.255.0!
What is the solution of the fault condition？（）
A.Configurationure Static IP Address on Client 1
B.Change the IP Address of VLAN 10 on DSW1
C.Add Permit any statement to access-list 10
D.Remove VLAN filter test1 from DSW1
最新試題
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）
Drag and drop the steps in the process for provisioning a cable modem to connect to a headendon the above to the below in the order defined by the DOCSIS standard.
IPSec VPN is a widely-acknowledged solution for enterprise network. Which three IPsec VPNstatements are true？（）
Drag and drop each management protocol on the above to the correct category on the below.
Drag the correct statements about MPLS-based VPN on the left to the boxes on the right.（Not allstatements will be used）
Drag the protocols that are used to distribute MPLS labels from the above to the target area on thebelow.（Not all options will be used）
A new router was configured with the following commands：The configuration above was found on an Internet Service Provider’s （ISP） Multiprotocol LabelSwitching （MPLS） network. What is its purpose？（）
As a network engineer， study the exhibit carefully. Router Net is unable to establish an ADSLconnection with its provider. Which action would correct this problem？（）
Study this exhibit carefully. What information can be derived from the SDM firewall configurationdisplayed？（）
This item contains several questions that you must answer. You can view these questions byclicking on the Questions button to the left. Changing questions can be accomplished by clickingthe numbers to the left of each question. In order to complete the questions， you will need to referto the SDM and the topology， neither of which is currently visible. To gain access to either thetopology or the SDK click on the button to left side of the screen that corresponds to the sectionyou wish to access. When you have finished viewing the topology the SDK you can return to yourquestions by clicking on the Questions button to the left.Which IPSec rule is used for the Olympia branch and what does it define？（）