Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Figure 2
Trouble Ticket Statement
Client 1 is getting an IP address from the DHCP server but is not able to ping DSW1 or the FTP
Cisco 642-832： Practice Exam
Server
Configurationon DSW1
vlan access-map test1 10drop
match ip address 10!
vlan filter test1 vlan-list 10!
ip access-list standard 10permit 10.2.0.0 0.0.255.255!
Interface VLAN10
ip address 10.2.1.1 255.255.255.0!
On which device is the fault condition located？（）
A.R4
B.DSW1
C.Client 1
D.FTP Server
您可能感興趣的試卷
你可能感興趣的試題
Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Figure 2
Trouble Ticket Statement
Client 1 is not able to reach the WebServer at 209.65.200.241. Initial troubleshooting shows that R1 isalso not able to reach the WebServer. R1 also does not have any active BGP neighbor.
Cisco 642-832： Practice Exam
Configon R1
router bgp 65001
no synchronization
bgp log-neighbor-changes
network 209.65.200.224 mask 255.255.255.252
neighbor 209.65.200.226 remote-as 65002
no auto-summary!
access-list 30 permit host 209.65.200.241
access-list 30 deny 10.1.0.0 0.0.255.255
access-list 30 deny 10.2.0.0 0.0.255.255!
interface Serial0/0/0/1
ip address 209.65.200.224 255.255.255.252
ip nat outside
ip access-group 30 in
What is the solution of the fault condition？（）
A.Add permit statement for 209.65.200.224/30 network in access list 30
B.Remove Deny Statements from access-list 30
C.Change neighbor 209.65.200.226 remote-as 65002 statement to neighbor 209.65.200.226 remote-as 65001
D.Use extended access-list instead of standard access-lis
Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Figure 2
Trouble Ticket Statement
Client 1 and Client 2 are not able to reach the WebServer at 209.65.200.241. Initial troubleshooting showsthat DSW1， DSW2 and all the routers are able to reach the WebServer
Cisco 642-832： Practice Exam
Configuration on R1
ip nat inside source list nat_pool interface Serial0/0/0/1 overload!
ip access-list standard nat_poolpermit 10.1.0.0!
interface Serial0/0/0/1
ip address 209.65.200.224 255.255.255.252
ip nat outside!
interfaceSerial0/0/0/0.12
ip address 10.1.1.1 255.255.255.252
ip nat inside
ip ospf message-digest-key 1 md5 TSHOOT
ip ospd authentication message-digest
What is the solution of the fault condition？（）
A.Add permit 10.2.0.0 statement in nat_pool access-list
B.Remove permit 10.1.0.0 statement from nat_pool access-list
C.Change ip nat inside source list nat_pool interface Serial0/0/0/1 overload to ip nat inside source listnat_pool interface Serial0/0/0/0.12 overload
D.Change ip nat outside statement under Serial0/0/0/1 configuration to ip nat inside
最新試題
cisco ios command to interface dialer 0
Match the xDSL type on the above to the most appropriate implementation on the below.
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）
Drag each element of the Cisco IOS Firewall Feature Set from the above and drop onto itsdescription on the below.
Drag the IPsec protocol description from the above to the correct protocol type on the below.（Notall descriptions will be used）Drag and Drop question， drag each item to its proper location.
Drag and drop the xDSL type on the above to the appropriate xDSL description on the below.
As a network technician， do you know what is a recommended practice for secure configurationmanagement？（）
Drag and drop the steps in the process for provisioning a cable modem to connect to a headendon the above to the below in the order defined by the DOCSIS standard.
Drag the DSL local loop topic on the left to the correct descriptions on the right.
Authentication is the process of determining if a user or identity is who they claim to be. Refer tothe exhibit. Which statement about the authentication process is correct？（）