Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Cisco 642-832： Practice Exam
Figure 2
Trouble Ticket Statement
HSRP has been configurationured between DSW1 and DSW2. DSW1 is configurationured to be activerouter but it never becomes active even though the HSRP communication between DSW1 and DSW2 isworking.
Configuration on DSW1
CertKiller.com
track 1 ip route 10.1.21.128 255.255.0.0 metric threshold threshold metric up 1 down 2!
track 10 ip route 10.2.21.128 255.255.255.0 metric threshold threshold metric up 63 down 64!
interface Vlan10
ip address 10.2.1.1 255.255.255.0
standby 10 ip 10.2.1.254
standby 10 priority 200
standby 10 preempt
standby 10 track 1 decrement 60
Configuration on R4
Cisco 642-832： Practice Examinterface loopback0
ip address 10.2.21.128 255.255.255.0
On which device is the fault condition located？（）
A.R4
B.DSW2
C.DSW1
D.R3
您可能感興趣的試卷
你可能感興趣的試題
Following ticket consists of a problem description and existing configuration on the device.
Figure 1
Cisco 642-832： Practice Exam
Figure 2
Trouble Ticket Statement：
Client 1 is able to ping 10.1.1.2 but not 10.1.1.1. Initial troubleshooting shows that R1 does not have anyOSPF neighbors or any OSPF routes
Configuration on R1：
router ospf 1
CertKiller.com
log-adjacency-changes
network 10.1.1.0 0.0.0.3 area 12
default-information originate always!
interfaceSerial0/0/0/0.12 point-to-point
ip address 10.1.1.1 255.255.255.252
ip nat inside
ip ospf message-digest-key 1 md5 TSHOOT
Configuration on R2：
router ospf 1
log-adjacency-changes
network 10.1.1.0 0.0.0.3 area 12!
Cisco 642-832： Practice Exam
interfaceSerial0/0/0/0.12 point-to-point
ip address 10.1.1.2 255.255.255.252
ip ospf authentication message-digest
ip ospf message-digest-key 1 md5 TSHOOT
What is the solution of the fault condition？（）
A.ipospf authentication message-digestcommand has to be added on S0/0/0/0.12
B.ipospf authentication message-digestcommand has to be added under the OSPF routing process
C.A static route to 10.1.1.4 must be added on R1
D.ipnat outside must be added on S0/0/0/0.12
A.Physical
B.Session
C.Application
D.Data-Link
E.Network
The following command is issued on a Cisco Router：
Router（configuration）#logging console warnings
Which alerts will be seen on the console？（）
A.Warnings only
B.debugging， informational， notifications， warnings
C.warnings， errors， critical， alerts， emergencies
D.notifications， warnings， errors
E.warnings， errors， critical， alerts
最新試題
IPSec VPN is a widely-acknowledged solution for enterprise network. What are the four steps tosetup an IPsec VPN？（）
IPSec VPN is a widely-acknowledged solution for enterprise network. Which three IPsec VPNstatements are true？（）
Authentication is the process of determining if a user or identity is who they claim to be. Refer tothe exhibit. Which statement about the authentication process is correct？（）
Drag and drop the xDSL type on the above to the appropriate xDSL description on the below.
Drag each element of the Cisco IOS Firewall Feature Set from the above and drop onto itsdescription on the below.
Drag the IOS commands from the left that would be used to implement a GRE tunnel using the10.1.1.0.30 network on interface serial 0/0 to the correct target area on the right.
Drag the DSL local loop topic on the left to the correct descriptions on the right.
Drag and drop each management protocol on the above to the correct category on the below.
Refer to the exhibit. Which two statements about the AAA configuration are true？（）
You need to configure a GRE tunnel on a IPSec router. When you are using the SDM to configurea GRE tunnel over IPsec， which two parameters are required when defining the tunnel interfaceinformation？（）