A. B200
B. C210
C. B250
D. C260
E. C460
您可能感興趣的試卷
你可能感興趣的試題
A. 800 MHz
B. 900 MHz
C. 1066 MHz
D. 1333 MHz
E. 1666 MHz
A. Dual-rank DIMMs are not supported.
B. 16-GB DIMMs are too slow.
C. The largest DIMM an Intel 55xx or 56xx CPU can address is 32 GB
D. The memory bus would be too long.
E. The blade would run too hot.
A. Missing control VLAN in VSM configuration
B. Missing packet VLAN in VSM configuration
C. VSM has no network connection to vCenter
D. VSM extension key is not installed on vCenter
E. vCenter extension key is not installed on VSM
The network administrator is adding a new N1Kv to the vCenter， however， the administrator does not see the new switch under the networking tab of vCenter.
The administrator issues the following command on the VSM to troubleshoot：
VSM# show svs connections
connection VC：
ip address： 10.10.10.30
remote port： 80
protocol： vmware-vim https
certificatE. default
datacenter namE. DC1
DVS uuiD. 67 32 30 50 a6 d2 49 64-9e 1c 5f 49 e3 af 55 99
config status： Disabled
operational status： Disconnected sync status： -
version： -
When attempting to fix the issue， the following error is seen：
VSM-PRI-188# conf
VSM-PRI-188（config）# svs connection VC
VSM-PRI-188（config-svs-conn）# connect
ERROR： [VMWARE-VIM] Extension key was not registered before its use
What is the cause of the error？（）
A. Missing control VLAN in VSM configuration
B. Missing packet VLAN in VSM configuration
C. VSM has no network connection to vCenter
D. VSM extension key is not installed on vCenter
E. vCenter extension key is not installed on VSM
Given the following configuration：
port-profile type ethernet DATA-UPLINK
vmware port-group
switchport trunk allowed vlan 1-3967，4048-4093
channel-group auto mode on
no shutdown
state enabled
port-profile type ethernet MGMT-UPLINK
vmware port-group
switchport trunk allowed vlan 10-12
channel-group auto mode on
no shutdown
state enabled
VEMs are seen to be joining and then are lost from the Cisco VSM. How would you resolve this issue？（）
A. Remove second NIC from each port profile
B. Remove VEM from VSM （no vem X）， remove NICs， and reinsert
C. Ensure that VLANs on uplink profiles are not overlapping
D. Reinstall VEM
E. Issue the command "module vem X execute vemcmd set pinning module vsm 1"
最新試題
An administrator creates a vNIC and assigns it to Fabric A with the fabric failover feature enabled. Which statement is true？（）
What would be the cause for the following fault in UCS Manager？（） "ether VIF x / xxx down， reason： ENM source pinning failed"
What is required for Cisco UCS C-Series rack server integration with Cisco UCS Manager？（）
On a Cisco Unified Computing System （UCS）， which two statements regarding Ethanalyzer are true？（）
Your company wants Server 1/eth0 （vNIC 1） configured so that it always uses Fabric Interconnect A Port Channel 1 （Po1） when it communicates with anything outside of the Cisco UCS domain. However， if vNIC 1 fails over to Fabric Interconnect B using fabric failover， then vNIC 1 can any uplink port on Fabric Interconnect B. Which statements are true？ （）
In a Cisco Unified Computing System， What is the "designated receiver" port in end-host mode used for？（）
What is the appliance port used to connect to in a Cisco Unified Computing System？（）
Given a Cisco Unified Computing System， which is a valid port type in end-host mode？（）
Server load balancing （SLB） is the process of deciding to which server a load-balancing device should send a client request for service. Which predictors are supported on ACE in order to select the best server to fulfill a client request？ （）
From the Cisco UCS CLI， how do you verify which uplink ports a blade server is using for its network connectivity？（）