通過以下命令查看主控板是否已經啟動NT自動保護？RTRV-EQPT::ALL;/* RTRV-EQPT::ALL */"P-OLT:LEEU,LEEU::,""RACK-1:ALTR-E,ALTR-E::,""SHELF-1-1:OLTS-M,OLTS-M:SHELFCLASS=MAINETHERNET:IS-NR,""ACU-1-1:AACU-C,AACU-C::IS-NR,""NTA:EHNT-B,EHNT-B::IS-NR,""NTB:EHNT-B,EHNT-B::IS-STBY,"

執行下面的兩條命令顯示如下：/* rtrv-ipport::acuenet:: */ "ACUENET:MANUAL:IPADDR=135.251.214.100,NETMASK=255.255.255.0,PHYADDR=00-07-72-ab-99-10"/* rtrv-ne-ALL::COM:: */"COM::MEMALM=\"RESET\",SHUTPREP=NOTREADY,DAYLIGHTSAVE=DISABLE,DEFROUTER=135.251.214.1,TZOFFSET=0,EPSSOAKINT=30000,CMDSSNTMO=150, SWRBALM=CLEAR,DBRBALM=CLEAR,AUTHSUPER=LOCAL,LANXMAC=00-07-72-ab-99-0e,AUTHDEF=REJECTALL,ACUSEC=DISABLED,SLIDMODE=ASCII,VOIPSCHEDMODE=DISABLED,SOAKMODE=DISABLE"此臺7342 OLT的地址是多少？

# configure la-agg-port 1 selection-policy mac-src actor-key 11 aggregatable aggregatable lacp-mode enable-lacp active-lacp passive-lacp# configure la-agg-port 5 selection-policy mac-src actor-key 11 aggregatable aggregatable lacp-mode enable-lacp active-lacp passive-lacp

在7302 cli中執行命令show interface Shub port，部分結果如下。isadmin># show interface shub port============================================================port table============================================================port admin-status oper-status speed type duplex------------------------------------------------------------------------------------------1 up up ten-mbps network half2 up down one-gb network full3 down down one-gb unused full============================================================以下說法錯誤的是：（）。

配置優先級隊列模板，要求Pbit為0的數據包，映射到隊列1，權重最高;Pbit為1,2，3，4，5的數據包，映射到隊列2，權重最低；Pbit為6.7的數據包，映射到隊列3，不使用隊列。PQ1WEIGHT=（）,PQ2WEIGHT=（）,PQ3WEIGHT=（）,PQ4WEIGHT=256,PQ5WEIGHT=256,PQ6WEIGHT=256,PQ7WEIGHT=256,PQ8WEIGHT=256,DOT1P0PQ=1,DOT1P1PQ=2,DOT1P2PQ=2,DOT1P3PQ=2,DOT1P4PQ=2,DOT1P5PQ=2,DOT1P6PQ=3,DOT1P7PQ=3"

7342 GPON通過什么命令可以將當前節點正在使用的OSWP committed？（）/* REPT-OPSTAT-OSWP::ALL */"OSWP-1:AVAILSTAT,ENABLED""OSWP-1:ACTSTAT,ACTIVE""OSWP-1:COMMITSTAT,UNCOMMITTED""OSWP-2:AVAILSTAT,EMPTY""OSWP-2:ACTSTAT,NOTACTIVE""OSWP-2:COMMITSTAT,UNCOMMITTED"

通過以下命令查看主控板是否已經啟動NT自動保護？RTRV-EQPT::ALL;/* RTRV-EQPT::ALL */"P-OLT:LEEU,LEEU::,""RACK-1:ALTR-E,ALTR-E::,""SHELF-1-1:OLTS-M,OLTS-M:SHELFCLASS=MAINETHERNET:IS-NR,""ACU-1-1:AACU-C,AACU-C::IS-NR,""NTA:EHNT-B,EHNT-B::IS-NR,""NTB:EHNT-B,EHNT-B::IS-STBY,"

# configure la-agg-port 1 selection-policy mac-src actor-key 11 aggregatable aggregatable lacp-mode enable-lacp active-lacp passive-lacp# configure la-agg-port 5 selection-policy mac-src actor-key 11 aggregatable aggregatable lacp-mode enable-lacp active-lacp passive-lacp

配置優先級隊列模板，要求Pbit為0的數據包，映射到隊列1，權重最高;Pbit為1,2，3，4，5的數據包，映射到隊列2，權重最低；Pbit為6.7的數據包，映射到隊列3，不使用隊列。PQ1WEIGHT=（）,PQ2WEIGHT=（）,PQ3WEIGHT=（）,PQ4WEIGHT=256,PQ5WEIGHT=256,PQ6WEIGHT=256,PQ7WEIGHT=256,PQ8WEIGHT=256,DOT1P0PQ=1,DOT1P1PQ=2,DOT1P2PQ=2,DOT1P3PQ=2,DOT1P4PQ=2,DOT1P5PQ=2,DOT1P6PQ=3,DOT1P7PQ=3"

在7300 FENT中執行命令show system ip，以下是結果信息。（）----------------- -------------------- -------------------device name IP address IP mask----------------- -------------------- -------------------Ethernet-PLIM 220.188.126.86 255.255.255.128ASAM 220.188.126.85default-gateway 220.188.126.1